Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. HIGH LEVEL CONNECTIONS (OPTIONAL) CAUTION! Before making any connections determine the type of radio to avoid possible damage to amplifier and/or radio. TWO CHANNEL CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) BASS POWER X-OVER BOOST RIGHT + RIGHT - LEFT - GREEN LEFT + GREEN/BLACK (NOT USED) GRAY/BLACK BLACK GRAY 94.7 GREEN BLACK GRAY/BLACK NOT USED GREEN/BLACK NOT USED GRAY RIGHT + LEFT + GROUND 94.7 TWO CHANNEL CONNECTIONS: COMMON GROUND RADIO ENGLISH 10 PWR/PRO BASS BOOST BASS BOOST CHIL 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE FL RL FR RR MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI PWR/PRO BASS BOOST BASS BOOST CHIL 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE FL RL FR RR MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI GRAY BLACK GRAY/BLACK (NOT USED) WHITE RIGHT + LEFT + GROUND WHITE BLACK GRAY/BLACK (NOT USED) WHITE/BLACK (NOT USED) GRAY RIGHT + WHITE/BLACK (NOT USED) LEFT + GROUND BA460 CONNECTIONS: COMMON GROUND RADIO 94.7 BA460 CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) RIGHT + RIGHT - LEFT - LEFT + GRAY GRAY/BLACK (NOT USED) WHITE/BLACK BLACK (GROUND) WHITE RIGHT + RIGHT - LEFT - LEFT + GRAY GRAY/BLACK (NOT USED) WHITE/BLACK BLACK (GROUND) WHITE 94.7 ENGLISH BA AMPLIFIERS 11 FUSE +12V REM GND SPEAKER AUX FUSE FUSE AUX OUTPUT + LCH - + RCH - BRIDGE +12V REM GND SPEAKER Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). SPEAKER CONNECTIONS + - + - BA1150, BA1300, BA1500 & BA1900D SPEAKER CONNECTIONS BRIDGED AUX OUTPUT AUX FUSE FUSE + - + - + - + - FL RL RR FR BRIDGED +12V REM GND BA460 SPEAKER CONNECTIONS BA2100, BA2150HC & BA260 SPEAKER CONNECTIONS + - 4 Ohm (2 Ohm Minimum) 4 Ohm (2 Ohm Minimum) 4 Ohm (2 Ohm Minimum) 4 Ohm (2 Ohm Minimum) ENGLISH 12 BRIDGE SPEAKER FUSE +12V REM GND LCH RCH SPEAKER CONNECTIONS (BRIDGED) The BA amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCA connections must be made. **CAUTION! In the bridged mode, the amplifier must see the recommended minimum impedance or higher. Any lower than the recommended minimum impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier! MINIMUM BRIDGED IMPEDANCE 4 Ohm Mono - BA260, BA2100, BA460 2 Ohm Mono - BA1150, BA1300, BA1500 1 Ohm Mono - BA2150, BA1900D + - BRIDGED AUX OUTPUT AUX FUSE FUSE + - + - + - + - FL RL RR FR BRIDGED +12V REM GND BA2100, BA2150HC & BA260 BRIDGED SPEAKER CONNECTIONS BA460 BRIDGED SPEAKER CONNECTIONS ENGLISH BA AMPLIFIERS 13 BRIDGE SPEAKER FUSE +12V REM GND LCH RCH CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier. SPEAKER CONNECTIONS (TRI-MODE) The BA260, BA460, BA2100, BA2150HC, are capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections. If you wish to use multiple speakers to achieve a lower impedance and higher power, it is strongly recommended that you seek professional advice from your BAZOOKA retailer before attempting to make these connections. Please Note: In the Tri-mode configuration, the amplifier’s built-in crossover must be set to the ”FLAT” position so the speakers receive full range output. NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D 100 F - + 100 F + - - 4 mH Left Mid / Tweeter 4 Ohm (2 Ohm Minimum) Mono Woofer 8 Ohm (4 Ohm Minimum) Right Mid / Tweeter 4 Ohm (2 Ohm Minimum) ENGLISH 14 PWR/PRO BASS BOOST BASS BOOST CHIL 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE FL RL FR RR MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI REMOTE BASS CONTROL MODULE (OPTIONAL) Bef...
Este manual também é adequado para os modelos :Unidade - BA2100 (6.53 mb)
Unidade - BA260 (6.53 mb)
Unidade - BA460 (6.53 mb)