Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in which you wish to mount the amplifier. Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well as a gas tank in the automobile. Make sure you know where they are when mounting the amplifier to avoid puncturing lines, shorting wires or drilling holes in the gas tank. Once you are ready, use a pencil to mark the mounting holes in the bottom panel. After you have marked the locations of the holes move amplifier out of the way and drill small starter holes to make the tapping screws easier to install. Use provided screws to tighten down the amplifier. PWR/PRO BASS BOOST BASS BOOST CHIL 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE FL RL FR RR MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI ENGLISH BA AMPLIFIERS 7 AUX FUSE FUSE AUX OUTPUT + LCH - + RCH - BRIDGE +12V REM GND SPEAKER CAR BATTERY +12V + - POWER CONNECTIONS 94.7 IN-LINE POWER FUSE MOUNTED WITHIN 12" FROM BATTERY RECOMMENDED (NOT PROVIDED) RADIO'S REMOTE TURN-ON OUTPUT Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using an 4 to 8 gauge power wire for your connections depending on the amplifier and length of the wire. Strip one end of the wire to connect to the terminal on the amplifier marked +12V. Loosen screw terminal and connect bare wire and tighten. Use caution to make sure no stray wire stands come in contact with surrounding terminals causing short circuits. Run the wire directly to the positive terminal of the car's battery. Make sure to use an in-line fuse within 12” of the car's battery to protect the electrical system and amplifier against short circuits and/or power surges. Connect the ground terminal of the amplifier to the car's chassis. For the ground connection, use an 4 to 8 gauge wire (black) to connect to the terminal marked GND and then connect it to the car's chassis. Try to keep the length of the cable as short as possible, preferably less than 6". Also make sure that the point on the car where the connection is to be made is free of paint and dirt. Connect the remote terminal of the amplifier to a switchable +12V source. This connection allows the amplifier to be turned on and off with the power control of the radio. If the radio has a REMOTE output terminal, connect it to the amplifier's terminal marked REMOTE (using a 16 gauge wire or heavier). Now when the radio is turned on, the amplifier will automatically turn on. This connection can also be made to the radio’s Power Antenna wire. IMPORTANT! Before making any connections, disconnect the car’s battery until the installation is completed to avoid possible damage to the electrical system. ENGLISH 8 SIGNAL CONNECTIONS Connect the RCA output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). Please note that when making these connections the signal inputs correspond with the speaker outputs. Optional full range line out connection to additional amplifiers in the system. BA2100 SIGNAL CONNECTIONS PWR/PRO BASS BOOST CHIL 0dB 12dB X-OVER 60Hz 130Hz LEVEL REMOTE INPUT OUTPUT L L R R MIN MAX PWR/PRO X-OVER 40Hz 130Hz LEVEL OUTPUT INPUT L L R R MIN MAX BASS PWR/PRO BOOST CHIL 0dB 12dB X-OVER 60Hz 400Hz LEVEL HI INPUT INPUT REMOTE L R MIN MAX FILTER LOW FLAT HI L R L R R L L R L R PWR/PRO BASS BOOST CHIL 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE FL RL FR RR MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI FRONT REAR L R R L BA460 SIGNAL CONNECTIONS BA1150, SIGNAL CONNECTIONS BA1300, BA1500, BA2150 &BA260 BA1900D SIGNAL CONNECTIONS ENGLISH BA AMPLIFIERS 9 BASS PWR/PRO BOOST CHIL 0dB 12dB X-OVER 60Hz 400Hz LEVEL HI INPUT INPUT REMOTE L R MIN MAX FILTER LOW FLAT HI BASS PWR/PRO BOOST CHIL 0dB 12dB X-OVER 60Hz 400Hz LEVEL HI INPUT INPUT REMOTE L R MIN MAX FILTER LOW FLAT HI BASS POWER X-OVER BOOST High Level inputs have been included to connect the amplifier to a radio without low-level outputs (i.e. factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. HIGH LEVEL CONNECTIONS (OPTIONAL) CAUTION! Before making any connections determine the type of radio to avoid possible damage to amplifier and/or...
Este manual também é adequado para os modelos :Unidade - BA2100 (6.53 mb)
Unidade - BA2150HC (6.53 mb)
Unidade - BA260 (6.53 mb)