Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
The gain controls should be adjusted very slowly. It may help to have another person to assist you by adjusting the gain controls while you listen for distortion. 15 TROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise. Before you can properly address the problem, you must first find the component that is causing the problem. This will take patience and a process of elimination. LOOK FOR.... SOLUTION No Output Blown fuse Bad RCA Cable(s) +12V at power terminal +12V at remote terminal Grounding point clean and tight Head Unit's fader not in center position Replace Replace Check connection Check connection Check for ground w/meter Set to center position Low Output Check level adjustments Bad RCA cable(s) Improper level matching Re-adjust Replace Re-adjust Engine Noise Grounding points are clean and tight Ground all components at same point Try different grounding point Bad RCA cable(s) Use High Quality shielded RCA cables Check for ground w/meter Ground at same point Change for better ground Replace Rejects inducted noise Low Vehicle charging system and/or battery Fix and/or replace Protection L.E.D. Illuminated Speaker short Check speakers connection for short circuit Speaker grounding out Make sure speaker wires do not touch chassis ground Impedance too low Check speaker impedance (Min 2 ohm Stereo, 4 Mono) Overheating Check mounting location for Adequate air Circulation Speaker impedance too low ENGLISH 16 BA AMPLIFIERS ENGLISH ENGLISH SPECIFICATIONS BA260 BA2100 BA2150HC BA1150 Max Power 300W 500W 1000W 300W Output Power @ 14.4 VDC : 4 ohm 60W x 2 100W x 2 140W x 2 100W x 1 2 ohm 85W x 2 150W x 2 220W x 2 150W x 1 Bridged 4ohm 170W x 1 300W x 1 450W x 1 N/A Bridged 2ohm N/A N/A 750W x 1 N/A Frequency Response + - 1dB 10Hz-25KHz 10Hz-25KHz 20Hz-25KHz 20Hz-130Hz S/N Ratio (A-weight) >96dB >96dB >98dB >99dB THD with 80k filter .06% .03% .20% .04% Low Input Level 200mV-6V 200mV-6V 200mV-6V 200mV-4V Hi Input Level 1.0V-10.0V 1.0V-10.0V N/A N/A Battery Voltage Range 11VDC-16VDC 11VDC-16VDC 11VDC-16VDC 11VDC-16VDC Crossover Type HP/FULL/LP HP/FULL/LP HP/FULL/LP LP Crossover Freq. Range 60Hz-400Hz 60Hz-400Hz 60- 400Hz *40Hz-130Hz Crossover Slope 12dB/Oct 12dB/Oct 18dB/Oct 12dB/Oct Bass EQ at FULL/LP 0-12dB @ 45Hz 0-12dB @ 45Hz 0-12dB @ 45Hz 0-12dB @ 45Hz Unbalanced Input (RCA Jack) Yes Yes Yes Yes Jack for Remote Control Yes Yes Yes No BA1300 BA1500 BA1900D BA460 Max Power 500W 750W 1200W 600W Output Power @ 14.4 VDC : 4 ohm 200W x 1 320W x 1 500W x 1 65W x 4 2 ohm 375 x 1 500W x 1 800W x 1 85W x 4 Bridged 4ohm N/A N/A N/A 175W x 2 Frequency Response + - 1dB 20Hz- 130Hz 20Hz-130Hz 20Hz-130Hz 10Hz-25KHz S/N Ratio (A-weight) >90dB >89dB >84dB >90dB THD with 80k filter .05% .07% .08% .03% Low Input Level 200mV-6V 200mV-6V 200mV-6V 200mV-6V Hi Input Level N/A N/A N/A 1.0V-10.0V Battery Voltage Range 11VDC-16VDC 11VDC-16VDC 11VDC-16VDC 11VDC-16VDC Crossover Type LP LP LP HP/FULL/LP Crossover Freq. Range *40Hz-130Hz *40Hz-130Hz *40-130Hz 60Hz-400Hz Crossover Slope 12dB/Oct 12dB/Oct 12dB/Oct 12dB/Oct Bass EQ at FULL/LP 0-12dB @ 45Hz 0-12dB @ 45Hz 0-12dB @ 45Hz 0-12dB @ 45Hz Unbalanced Input (RCA Jack) Yes Yes Yes Yes Jack for Remote Control Yes Yes Yes Yes * Low-pass Only Due to continuing product improvement, specifications subject to change without notice. 17 LIMITED WARRANTY Southern Audio Services, Inc., warrants all products to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. In the event the product is not as warranted, SAS’ sole obligation shall be to repair or replace the defective product at SAS’ option: SAS limits its obligation under any implied warranties under state laws to a period not to exceed the limited warranty period. SAS and its authorized BAZOOKA® dealers specifically disclaim liability for any incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state. What is covered: This warranty covers all defects in materials or workmanship (parts and labor) in the product. What is not covered: This warranty does not cover the following: 1. Damages occurring during shipment of the product to SAS for repair (Claims must be presented to the carrier). 2. Damages caused by accident, abuse, negligence, misuse or improper Operation or installation. 3. Damages caused by an act of God, including withou...
Este manual também é adequado para os modelos :Unidade - BA2100 (6.53 mb)
Unidade - BA2150HC (6.53 mb)
Unidade - BA460 (6.53 mb)