|
Facilidade de uso
Take care not to over tighten nut. Tighten only until end of bolt is flush with outside of nut. NOTE: If you have a torsion spring counterbalance system, it will be necessary to raise the opener and support it on a step ladder to attach the front end of the rail assembly to the wall bracket. The upper door arm is secured to the spacer bracket with one tie wrap for shipping. Remove tie wrap attaching upper door arm to the spacer bracket, allowing door arm to swing down (see caution). CAUTION: Support upper door arm with your free hand, to prevent door arm from swinging down uncontrolled. 4 Positioning Motor End of Opener Tools Needed: 2” x 4” Board Non-Metallic Step Ladder IMPORTANT: TO PREVENT DAMAGE TO DOOR, DO NOT REST THE OPENER ON THE DOOR WITHOUT USING A 2” X 4” BOARD AT LEAST 3 FEET LONG. Raise the motor end of the opener and support it so you can open the door to its fully open position. You may need help raising motor end if ladder is not high enough. IMPORTANT: TO PREVENT DAMAGE TO DOOR OR OPENER, POSITION TROLLEY AS CLOSE TO OPENER AS POSSIBLE, BEFORE OPENING DOOR. Open the door and place a 2” x 4” x 36” minimum board along the top section of the garage door. Rest the rail assembly on the 2” x 4” board. Support top section of door to prevent excessive sagging. Front Wall Bracket 1/4” Plastic Insert Locking Nut 1/4” x 4” Hex Head Bolt Non-Metallic Step ladder Support Door to Prevent Sagging Door 2” x 4” Board Opener Rail Assembly Tie Wrap Upper Door Arm Spacer Bracket Upper Door Arm Trolley Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at Cardboard or Cloth to Protect the Housing Rail Assembly 3 Attach Unit to Front Wall Bracket Tools Needed: 7/16” Socket Ratchet Wrench Adjustable Wrench Raise the front end of the rail assembly and attach it to the front wall bracket, using the 1/4” x 4” hex head bolt and the supplied 1/4” plastic insert locking nut. Take care not to over tighten nut. Tighten only until end of bolt is flush with outside of nut. NOTE: If you have a torsion spring counterbalance system, it will be necessary to raise the opener and support it on a step ladder to attach the front end of the rail assembly to the wall bracket. The upper door arm is secured to the spacer bracket with one tie wrap for shipping. Remove tie wrap attaching upper door arm to the spacer bracket, allowing door arm to swing down (see caution). CAUTION: Support upper door arm with your free hand, to prevent door arm from swinging down uncontrolled. 4 Positioning Motor End of Opener Tools Needed: 2” x 4” Board Non-Metallic Step Ladder IMPORTANT: TO PREVENT DAMAGE TO DOOR, DO NOT REST THE OPENER ON THE DOOR WITHOUT USING A 2” X 4” BOARD AT LEAST 3 FEET LONG. Raise the motor end of the opener and support it so you can open the door to its fully open position. You may need help raising motor end if ladder is not high enough. IMPORTANT: TO PREVENT DAMAGE TO DOOR OR OPENER, POSITION TROLLEY AS CLOSE TO OPENER AS POSSIBLE, BEFORE OPENING DOOR. Open the door and place a 2” x 4” x 36” minimum board along the top section of the garage door. Rest the rail assembly on the 2” x 4” board. Support top section of door to prevent excessive sagging. Front Wall Bracket 1/4” Plastic Insert Locking Nut 1/4” x 4” Hex Head Bolt Non-Metallic Step ladder Support Door to Prevent Sagging Door 2” x 4” Board Opener Rail Assembly Tie Wrap Upper Door Arm Spacer Bracket Upper Door Arm Trolley 5 Mounting Opener End Ceiling Joist Gear Cap Nut/ Bolt Opener Cut Perforated Angles to Fit Alternate Hanger Mounting Holes Tools Needed: Power Drill Hacksaw 1/8” Drill Bit 1/2” Socket 7/16” Socket Ratchet Wrench Adjustable Wrench Tape Measure Perforated Angle Iron (Not Supplied) CAUTION: Do not use gear cap bolt or nut for hanger attachment. This may cause sprocket, chain or Belt misalignment, resulting in damage to opener or possible personal injury! Align the center of opener’s rail assembly with the center line previously marked on the top section of the garage door to ensure rail will be parallel with the direction of door travel. Using perforated angles (cut to proper length) hang opener end from ceiling joist. Be sure to locate and mount to ceiling joists, as illustrated. Pilot drill with 1/8” drill bit and use 1/4” x 1-1/2” lag screws (not supplied) to ensure a rigid mount. Attach opener to perforated angles using 5/16” x 3/4” bolts, 5/16” lock washer, and 5/16” nuts (not supplied). NOTE: Bracing should be at an angle to provide rigid support. When opener is securely attached to perforated angles, remove the 2” x 4” (used to support rail assembly in Step 4) and close the door. NOTE: It is recommended that 10’ rails be supported in the center to prevent sagging. Opener rail should be aligned perpendicular to the garage door when properly installed. ...
Este manual também é adequado para os modelos :Portão automático - PRODRIVE 3220C (4.85 mb)
Portão automático - PRODRIVE 3220C-Z (4.85 mb)
Portão automático - PRODRIVE 3221C-Z (4.85 mb)
Portão automático - PRODRIVE 3222C (4.85 mb)