Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
1. FOR PORTLAND TRACK: The horizontal tracks are stamped with radius on the side of the horizontal track, as shown in FIG. 1.1. NOTE: If necessary, remove the upper arm (straight arm) from the trolley, to use the lower arm (curved arm). Remove the hairpin cotter from the clevis pin at the front of trolley and slide clevis pin out far enough to slide the upper arm out between the left and right side of trolley body. Position the lower door arm so the end with the single hole lines up with the clevis pin. Slide clevis pin completely back into trolley and reinstall hairpin cotter. LOW HEADROOM: If you have low headroom track, as shown in FIG. 1.6 on page 24, then proceed with “Low Headroom Trolley Positioning Charts” on page 24. STANDARD LIFT: Using the STANDARD LIFT TROLLEY POSITIONING CHARTS, refer to DIM “X” to set the distance from header to trolley, as shown in FIG. 1.2. NOTE: Depending on your setup, you may have to cut straight arm to accomplish trolley settings. If adjustment of the trolley position is required, use the close travel adjustment screw located on the bottom of the opener, as shown in FIG 1.5 on page 24. A 1/4 turn equals approximately 1” of trolley travel; turn clockwise to decrease distance (forward) and counter-clockwise to increase distance (forward). NOTE: Proceed with “Connecting Door Arm To Door” Step 18, on page 14. STANDARD LIFT TROLLEY POSITIONING CHART FOR (MODEL 9700) 15” RADIUS DIM “X” TYPE OF ARM BEING USED REFERENCE ILLUSTRATIONS 10 9/16”- 14 5/8” STRAIGHT / CURVED FIG. 1.3 ..Setting Trolley Close Position/ Connecting Door Arm (Models 9100, 9400, 9600, 5120, 5140 & 9700) With TorqueMaster® Or Extension Springs FIG. 1.3 Cut Straight Arm To Accomplish Trolley Setting Curved Arm Straight Arm FIG. 1.4 Straight Arm Curved Arm Cut Straight Arm To Accomplish Trolley Setting 12”Stamped Radius 12” FIG. 1.1 Horizontal Track FIG. 1 Horizontal Track 12” OR 15” STANDARD LIFT TROLLEY POSITIONING CHART FOR (MODELS 9100, 9400, 9600, 5120 & 5140) 10” AND 12” RADIUS DIM “X” TYPE OF ARM BEING USED REFERENCE ILLUSTRATIONS 11 1/2” CURVED / STRAIGHT FIG. 1.4 STANDARD LIFT TROLLEY POSITIONING CHART FOR (MODELS 9100, 9400, 9600, 5120 & 5140) 14” AND 15” RADIUS DIM “X” TYPE OF ARM BEING USED REFERENCE ILLUSTRATIONS 13”-15” CURVED / STRAIGHT FIG. 1.4 FIG. 1.2Top Section 10”, 12”, 14”, OR 15” Standard Lift Track “X” Clevis Pin Hairpin Cotter Trolley TOP VIEW Tools Needed: Needle Nose Pliers Adjustable Wrench Ratchet Wrench 7/16” Socket 9/16” Socket Hacksaw Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at Setting Trolley Close Position/ Connecting Door Arm (Continued) LOW HEADROOM: Using the LOW HEADROOM TROLLEY POSITIONING CHARTS, refer to DIM “X” to set the distance from header to trolley, as shown in FIG. 1.6. NOTE: Depending on your setup, you may or may not have to cut straight arm to accomplish trolley settings. If adjustment of the trolley position is required, use the close travel adjustment screw located on the bottom of the opener, as shown in FIG 1.5. A 1/4 turn equals approximately 1” of trolley travel; turn clockwise to decrease distance (forward) and counter-clockwise to increase distance (forward). LOW HEADROOM TROLLEY POSITIONING CHART FOR (MODELS 9100, 9400, 9600, 5120 & 5140) REFERENCE TYPE OF ARM DIM “X” ILLUSTRATIONS BEING USED TO THE RIGHT CURVED / 14 1/2” FIG. 1.7 STRAIGHT OPTIONAL HOOKUP 10” - 14” STRAIGHT FIG. 1.7a LOW HEADROOM TROLLEY POSITIONING CHART FOR (MODEL 9700) TYPE OF ARM REFERENCE DIM “X” BEING USED ILLUSTRATIONS 14 3/4” CURVED / FIG. 1.7 17 11/16” STRAIGHT OPTIONAL HOOKUP 10” - 14” STRAIGHT FIG. 1.7a NOTE: Proceed with “Connecting Door Arm To Door” Step 18, on page 14. OPEN CLOSE MORE LESS MORE TRAVEL ADJUSTMENT FIG. 1.5 Low Headroom Track Top Section “X” FIG. 1.6 Curved Arm Cut Straight Arm To Accomplish Trolley Setting FIG. 1.7 Bottom Of Opener FIG. 1.7a Straight Arm Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at DETERMINE THE WAYNE-DALTON TRACK RADIUS BEING USED: FOR MOUNT HOPE AND PENSACOLA TRACK: Measure the curved ends of the horizontal track to determine if you have a 12” or 15” radius horizontal track, as shown in FIG. 1. FOR PORTLAND TRACK: The horizontal tracks are stamped with radius on the side of the horizontal track, as shown in FIG. 1.1. NOTE: If necessary, remove the upper arm (straight arm) from the trolley, to use the lower arm (curved arm). Remove the hairpin cotter from the clevis pin at the front of trolley and slide clevis pin out far enough to slide the upper arm out between the left and right side of trolley body. Position the lower door...
Este manual também é adequado para os modelos :Portão automático - PRODRIVE 3220C (4.85 mb)
Portão automático - PRODRIVE 3220C-Z (4.85 mb)
Portão automático - PRODRIVE 3221C (4.85 mb)
Portão automático - PRODRIVE 3221C-Z (4.85 mb)