1 Sample Wall Mount and Table Top CV Touch Panels ATTENTION! Verify you are using the latest NetLinx Master Firmware (available from on your ME260/64 and NI-Series Controllers. Verify the TPDesign4 program being used is Version 2.4 or higher. Overview The 12" (NXT/NXD-CV12) and 15" (NXT/NXD-CV15) Video panels are 4th generation graphics touch panels that provide richer colors and crisper contrast than any panels currently on the market. Modero tilt panels now come with an optional NXA-BASE/B bat

Memory: •256 MB on-board memory •128 MB Compact Flash (upgradeable to 1 GB factory programmed) Weight: •NXD-1200V: 10.80 lbs (4.90 kg) •NXT-1200V: 10.80 lbs (4.90 kg) LCD Parameters: •Aspect Ratio: 4:3 •Brightness (luminance): 250 cd/m2 •Channel transparency: 8-bit Alpha channel transparency •Contrast ratio: 300:1 •Display area (HW): 183.10 mm x 247.40 mm •Display colors: 256K (18-bit color depth) •Dot/Pixel pitch: 0.297 mm •Screen resolution (HV): 800 x 600 pixels •Video formats: NTSC, PAL, and

1 Wall Mount and Table Top 1500VG Touch Panels NXD-1500VGNXT-1500VG(Wall Mount) (Table Top) Verify you are using the latest NetLinx Master and Modero touch panel firmware (available from Verify the TPDesign4 program being used is Version 2.6 or higher. Overview The VG-Series of touch panels can be fitted for either Video (Composite) or RGB (Component) via the use of two kit configurations: Video Kit and RGB Kit. Each kit comes with its own group of standard components that are specific to its co

1 4 7 8 9 6 32 5 @SHO Syntax: Sets a specific "’@SHO’,," button to on or off. Variables: variable text address = 1 - 255 button on/off: 0 = button Off 1 = button On Example: SEND_COMMAND TP,"’@SHO’,128,0" Sets button 128 off. @TXT Adds text to a button. Use the | character to display text on multiple lines. Syntax: "’@TXT’,,’’" Variables: variable text address = 1 - 255 button text = Enter button text to appear on button. Example

1. Cut out the surface for the WDS using the dimensions shown in installation diagram SP-5965-01 (reproduced in FIG. 11 on page 10). It is recommended that you cutout the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments. Be sure to cut out the four notches along the sides to accommodate the four drywall expansion clips (included). When installing the four #6-32 Mounting Screws in Step 3, turn the screwdriver gently

The panel must also be connected to the Controller via a mini-AXlink connection. If power is lost during the download process, the unit powers up with the same set of code prior to the download. There is a small window during which a loss of power can be catastrophic. If power is lost between the erase of flash memory and the completion of copying the new boot code from RAM to flash memory, the unit will not operate at all when power returns. If you have not already installed the SoftROM program

The page password range is 1-5,999. • CLEAR Clears the number in the keypad display. • ENTER Sets the page password number, closes the keypad, and returns to the Protected Setup page. Calibrate Press CALIBRATE to open the CALIBRATE decision button shown in Figure 103 and reset the vertical and horizontal touch points on the LCD. • YES Starts the calibration process. Carefully press each crosshair that appears using your finger or dull pointer. When the calibration process is complete, press

• Cancel - discard changes and return to the previous page. Refer to the EAP Authentication section on page 166 and the Using the Site Survey tool section on page 23 for further details on these security options. 80 MVP-5200i Modero Viewpoint Widescreen Touch Panel Protected Setup Pages EAP-TLS Settings Press the EAP-TLS button to open the EAP-TLS Settings page (FIG. 72). FIG. 72 Wireless Settings page - EAP-TLS Settings TLS (Transport Layer Security) was the original standard wireless L

Light Sensor: Allows you to monitor and alter the sensitivity of the Modero panel light sensor: • The Light Sensor Level field indicates the level used to report the light sensor level back to the NetLinx Master (set in TPD4) (read-only). • The Light Sensor Level Port field indicates the port used to report the light sensor level back to the NetLinx Master (set in TPD4) (read-only). • The Light Sensor Channel field indicates the level used to report the sensor channel back to the NetLinx Master

.. From the Online Tree tab of the Workspace window, select the NetLinx Master. .. Follow steps outlined in either the Obtaining or Assigning the Master’s IP Address sections from your particular NetLinx Master instruction manual to use an address. .. Note the IP Address and Gateway information. 2. Launch NetLinx Studio 2.3 (default location is Start > Programs > AMX Control Disc > NetLinx Studio > NetLinx Studio 2.3). 3. Select Settings > Master Communication Settings, from the Main menu to ope