Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
- HI PASS: 100 Hz - LOW PASS: N/A Interconnect cable checklist: - Using good quality RCA cables, feed the front and rear outputs of a head unit to 1 channel bass amplifier: the inputs of the 4 channel amplifier as shown. - Subsonic filter: 10 Hz to 40 Hz - Also connect the LINE OUT of the 4 channel amplifier to the LINE INPUT of the - LOW PASS: 80 Hz 1 channel amplifier as shown. Please note that these frequency points are suggestions only. Refer to the Mono bass woofer wiring: loudspeaker manufacturer specifications and the section “Setting up systems Connect the mono speaker positive terminal to the LEFT +, and its negative after installation for best performance” terminal to RIGHT -. Level control checklist: Switch setting checklist: - Refer to the section “Setting up systems after installation for best performance” 4 channel highs amplifier: - 1/2CH X-OVER: HI Minimum final loudspeaker impedances: - 3/4CH X-OVER: HI 4 Channel Amplifier: Crossover frequency control checklist: - 2 ohm per channel in stereo mode. - 4 channel highs amplifier: - 4 ohm mono bridged. Channels 1/2: 1 Channel Amplifier: - HI PASS: 100 Hz - 1-Ohm to 4-Ohms LOW PASS: N/A STEREO INTERCONNECT RCA CABLE Interconnect cable checklist: Level control checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the - Refer to the section “Setting up systems after installation for best full range primary amplifier with good quality RCA cables. A “Y” adapter performance” may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring. These amplifiers have dual speaker terminals, simplifying the hookup of multiple speakers. The 2 positives are one block and the 2 negatives are one block. It does not matter which positive or negative you select since the amplifier sees the sum of the load. Crossover frequency control checklist: - LOW PASS: 35Hz to 250Hz - SUBSONIC:15 Hz to 35 Hz - BASS EQ: 0 to 10dB - PHASE: 0 to 180 degrees Minimum final loudspeaker impedance: - 1 ohm. FULL RANGE STEREO LINE INPUT NOT USED Y-ADAPTOR Note: You can use the Radio/CD designated mono line output or a full range stereo line output. For full range stereo line output, you will need an optional “Y-Adaptor” as shown * INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB PROTPEOCWTER BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz SP-E A K E R - O U T P U T+ + GND REM BA TT+12V POWER INPUT FUSE INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB PROTPEOCWTER BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz SP-E A K E R - O U T P U T+ + GND REM BA TT+12V POWER INPUT FUSE HFR-3 MIN MAXX BOOST 5 GLX1000.1D / GLX1400.1D / GLX1800.1D MONO AMPLIFIER APPLICATIONS Basic application HFR-3 MIN MAXX BOOST REMOTE TURN-ON CHASSIS GROUND TO BATTERY +12v VIA FUSE PARALLEL MONO SUBWOOFERS 2-OHMS SVC EACH MINIMUM, or 4-OHMS DVC EACH MINIMUM MONO SUBWOOFERS Dual Subwoofer Application REMOTE TURN-ON CHASSIS GROUND TO BATTERY +12v VIA FUSE MONO SUBWOOFER 1-OHM MINIMUM DESIGNATED M*ONO LINE INPUT DESIGNATED M*ONO LINE INPUT INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB PROTPEOCWTER BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz BA POWERT TIN+P12UVT GND SPERAEKME R O U -T P U T - + + INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB PROTPEOCWTER BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz BA POWERT TIN+P12UVT GND SPERAEKME R O U -T P U T - + + HFR-3 MIN MAXX BOOST 6 GLX1800.1D MONO AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the Minimum final loudspeaker impedance: full range primary amplifier with good quality RCA cables. A “Y” adapter - 1 ohm. may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring. These amplifiers have dual speaker terminals, simplifying the hookup of multiple speakers. The 2 positives are the same and the 2 negatives are the same. Crossover frequency control checklist: - LOW PASS: 35Hz to 250Hz - SUBSONIC:15 Hz to 35 Hz - BASS EQ: 0 to 10dB - PHASE: 0 to 180 degrees Level control checklist: - Refer to the section “Setting up systems after installation for best performance” FULL RANGE STEREO LINE INPUT NOT USED Y-ADAPTOR Note: You can use the Radio/CD designated mono line output or a full range stereo line output. For full range stereo line output, you will need an optional “Y-Adaptor” as shown * HFR-3 MIN MAXX BOOST REMOTE TURN-ON CHASSIS GROUND TO BATTERY +12v VIA FUSE PARALLEL MONO SUBWOOFERS 2-OHMS SVC EACH MINIMUM, or 4-OHMS DVC EACH MINIMUM MONO SUBWOOFERS Dual Subwoofer Application REMOTE TURN-ON CHASSIS GROUND TO BATTERY +12v VIA FUSE MONO SUBWOOFER 1-OHM MINIMUM DESIGNATED M*ONO LINE INPUT DESIGNATED M*ONO LINE INPUT INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB OUT IN PRPOOTWECETR MAOSUTTEPRUT SLINAPUT VE BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz BA POWERT TI...
Este manual também é adequado para os modelos :Avtousiliteli - GLX100.4 (3.69 mb)
Avtousiliteli - GLX1400.1D (3.69 mb)
Avtousiliteli - GLX1800.1D (3.69 mb)
Avtousiliteli - GLX2200.1D (3.69 mb)