Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
A “Y” adapter - 1 ohm. may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring. These amplifiers have dual speaker terminals, simplifying the hookup of multiple speakers. The 2 positives are the same and the 2 negatives are the same. Crossover frequency control checklist: - LOW PASS: 35Hz to 250Hz - SUBSONIC:15 Hz to 35 Hz - BASS EQ: 0 to 10dB - PHASE: 0 to 180 degrees Level control checklist: - Refer to the section “Setting up systems after installation for best performance” FULL RANGE STEREO LINE INPUT NOT USED Y-ADAPTOR Note: You can use the Radio/CD designated mono line output or a full range stereo line output. For full range stereo line output, you will need an optional “Y-Adaptor” as shown * HFR-3 MIN MAXX BOOST REMOTE TURN-ON CHASSIS GROUND TO BATTERY +12v VIA FUSE PARALLEL MONO SUBWOOFERS 2-OHMS SVC EACH MINIMUM, or 4-OHMS DVC EACH MINIMUM MONO SUBWOOFERS Dual Subwoofer Application REMOTE TURN-ON CHASSIS GROUND TO BATTERY +12v VIA FUSE MONO SUBWOOFER 1-OHM MINIMUM DESIGNATED M*ONO LINE INPUT DESIGNATED M*ONO LINE INPUT INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB OUT IN PRPOOTWECETR MAOSUTTEPRUT SLINAPUT VE BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz BA POWERT TIN+P12UVT GND SPERAEKME R O U -T P U T - + + INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB OUT IN PRPOOTWECETR MAOSUTTEPRUT SLINAPUT VE BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz BA POWERT TIN+P12UVT GND SPERAEKME R O U -T P U T - + + INPUT OUTPUT INPUT LEVEL PHASE REMOTE BAS EQ SONIC LOW P ASS L L R R SUB OUT IN PRPOOTWECETR MAOSUTTEPRUT SLINAPUT VE BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz BA POWERT TIN+P12UVT GND SPERAEKME R O U -T P U T - + + DUAL AMP INSTALLATION PROCEDURE: 4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse. 1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out 5. Connect two 0 gauge ground cables directly to the chassis with in 36” of the amp. puts with good quality RCA interconnect cables. - Be sure to remove any paint or primer from the ground point. 2. Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack on the - Use a nut, bolt and lock washer to secure the ground cable to the chassis ground. Master amp. This will allow the Master amp to control both Master and Slave amps 6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position. with just one Bass Remote. Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position. 3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the 7. Connect the subwoofer(s) in accordance to the diagrams below. Slave amp SLAVE INPUT. Note: This will “link” the amps so that the Master amp 8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as crossover switches will control both the Master and Slave amps. The Slave amp shown below. crossover switches will be bypassed. SINGLE AMP INSTALLATION PROCEDURE: 1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables. 2. Plug in the HFR-3 remote module into the amp REMOTE INPUT jack. 3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse. 4. Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp. - Be sure to remove any paint or primer from the ground point. - Use a nut, bolt and lock washer to secure the ground cable to the chassis ground. 5. Connect the subwoofer(s) in accordance to the diagrams below. 6. Make sure the MASTER/SLAVE switch is in the MASTER position. Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position FULL RANGE STEREO LINE INPUT NOT USED Y-ADAPTOR Note: You can use the Radio/CD designated mono line output or a full range stereo line output. For full range stereo line output, you will need an optional “Y-Adaptor” as shown. GLX2200.1D MONO AMPLIFIER APPLICATIONS Basic application HFR-3 MIN MAXX BOOST +12V GND POWER SPEAKER REM - - + + MONO SUBWOOFER REMOTE TURN-ON CHASSIS GROUND TO BATTERY + 12 Volts VIA FUSE PARALLEL MONO SUBWOOFERS 2 OHMS EACH MINIMUM Linking two amps for single or dual subwoofer application Amplifiers are stable to 2-Ohms linked 7 HFR-3 MIN MAXX BOOST 12 GAUGE JUMPER WIRE RCA JUMPER CABLE MASTER OUTPUT T O SLA VE INPUT DESIGNATED MONO OUTPUT FROM HEAD UNIT DESIGNATED MONO OUTPUT FROM HEAD UNIT Master remote controls both amplifiers when LINKED OUTPUT MASTER INPUT SLAVE IN OUT OUTPUT MASTER INPUT SLAVE IN OUT (MASTER) (SLAVE) 8 SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE GLX1000.1D / GLX1400.1D / GLX1800.1D / GLX2200.1D General: At this point you are ready to get more specific on the settings for your amplifier. Subsonic: This setting acts as a low frequency cut off for your system bass reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The ...
Este manual também é adequado para os modelos :Avtousiliteli - GLX100.4 (3.69 mb)
Avtousiliteli - GLX1000.1D (3.69 mb)
Avtousiliteli - GLX1400.1D (3.69 mb)
Avtousiliteli - GLX2200.1D (3.69 mb)