If the chain is too loose, it will sag below the bar. tGuideBarChainAdjustmenBar Nuts Adjusting Tool (Bar Tool) Screw Adjusting the tension: Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time before you start the chain saw. 1. Loosen bar nuts until they are finger tight against the clutch cover. 2. Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Included with this saw is a 3.2 ounce (95 ml) container of Poulan/WEED EATER brand synthetic oil. Pour the entire contents of this container into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture. DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION. CAUTION: Never use straight gasoline in your unit. This will cause

CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. NOTE: It is normal for a small amount of oil to appear under the saw after engine stops. Do not confuse this with a leaking oil tank. S ON/STOP Switch - --Ensure ON/STOP switch functions properly by moving the switch to the STOP position. Make sure engine stops; then restart engine and continue. S Fuel Tank - --Do not use saw if fuel tank shows signs of damage or leaks. S Oil Tank - --D

Veuillez ne pas retourner le produit au detaillant. 1- --800- --554- --6723 Register your product online at: Registre su producto en linea en: Enregistrez votre produit en ligne a l’adresse : Instruction Manual Manual de Instrucciones Manuel d’Instructions 1420 1630 WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e instrucciones

CARTON CONTENTS S Chain Saw (fully assembled) S Bar Sheath Examine parts for damage. Do not use damaged parts. NOTE: If youneed assistanceor find that parts are missing or damaged, please call 1-800-554-6723. ASSEMBLY Your unit is fully assembled; no assembly is required. 6 OPERATIONOPERATION KNOW YOUR SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and ad

Removebarclamp. DriveSprocket Bar Knob Bar Clamp 8. Pull guide bar forward until the chain CHAIN ADJUSTMENT is snug in the guide bar groove. Ensure all drive links are in the bar groove. 9. Install bar clamp. Be sure adjusting pin is in the adjusting pin hole in the guide bar. CAUTION: It is very important when installing the bar clamp that the adjusting pin aligns into the adjusting pin hole in the bar. Failure to install the bar clamp correctly may result in permanent damage to your chain saw.

DirectionofFall45_ Planaclearretreatpath FELLING LARGE TREES (6 inches (15 cm) in diameter or larger) The notch method is used to fell large trees. A notch is cut on the side of the tree in the desired direction of fall. After a felling cut is made on the opposite side of tree, the tree will tend to fall into the notch. NOTE: If the tree has large buttress roots, remove them before making the notch. If using saw to remove buttress roots, keep saw chain from contacting ground to prevent dulling o

ATTACHING THE BAR & CHAIN (If not already attached) WARNING: If received assembled, repeat all steps to ensure your saw is properly assembled and all fasteners are secure. Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not moving! 1. Loosen and remove the bar nuts and the clutch cover from the saw. 2. Remove the plastic shipping spacer (if present). Clutch cover Bar nuts Location of shipping spacer Chain adjustment tool (Bar Tool) 3. Turn adjusting

For example, if improper tools are used to remove or hold the flywheel when servicing the clutch, structural damage to the flywheel can occur and cause the flywheel to burst. S Make certain the saw chain stops moving when the throttle trigger is released. For correction, refer to CARBURETOR ADJUSTMENTS. S Never modify your saw in any way. S Keep the handles dry, clean, and free of oil or fuel mixture. S Keep fuel and oil caps, screws, and fasteners securely tightened. S Use only Poulan accessori

m Shreveport, Louisiana 71129 mmh /1-800-554-6723? SEE BACK COVER FOR DETAILS! TABLE OF CONTENTS WARNINGS AND SAFETY INSTRUCTIONS 3 TYPES OF CUTTING......... KNOW YOUR UNIT......................... 6 GENERAL MAINTENANCE .. PARTS & SERVICE............... Back Cover SPECIFICATIONS I25-147EL-14 PATRIOT | 1626-167EL-X6 PATRIOT POWER SUPPLY: SPROCKET/DRIVE: RATED CURRENT: MAXIMUM MOTOR OUTPUT: Non Chrome Cutters LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATT