Log:
Downloads : 1   Arquivo Tamanho: 769 kb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

26632750200 36832057200 99461050304 FRAME,HANDLE HANDLE,FRONT COLLAR,DAMPER B DAMPER,B WASHER,BRAKE SHAFT BOLT,HEX,5X30S 1 1 4 4 4 4 6-7 6-8 6-9 6-10 6-11 5053329020 0403316080 99051050403 99210050062 99201050061 CLIP SUPPORT,HANDLE BOLT,HEX,5X40 WASHER,S,5 WASHER,5 1 1 2 2 2 Page 7 custsvc@nikko-tanaka-usa.com PARTS INFORMATION THT-210S REAR HANDLE • FIGURE 7 ITEM PART NUMBER DESCRIPTION QTY COMMENTS 7-1 0513329020 HANDLE,B 1 7-2 0503329020 HANDLE,A 1 7-3 2303329020 LEVER,THROTTLE 1 7-4 2313329

Downloads : 5   Arquivo Tamanho: 645 kb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

Depth gauge 10. Correct angle on top plate (degree of angle depends on chain type) 11. Slightly protruding "hook" or point (curve on non-chisel chain) 12. Top of depth gauge at correct height below top plate 13. Front of depth gauge rounded off LOWERING DEPTH GAUGES WITH A FILE 1) If you sharpen your cutters with a file holder, check and lower the depth. 2) Check depth gauges every third sharpening. 3) Place depth gauge tool on cutter. If depth gauge projects, file it level with the top of the t

Downloads : 9   Arquivo Tamanho: 2 mb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

29) Install the chain and bar on the motor unit as follows: 1.Secure the chain around the motor unit’s sprocket. Ensure that its teeth correspond with the direction of rotation according to the arrow (A). 2. Position the bar and thread the chain around the bar. CAUTION! Ensure that the tip of the tension screw’s nut (B) fits into the hole on the bar. 3. Install the guide (C) and loosely tighten the two bar bolts (just so that there is no play on the bar). 4. Adjust the chain using the tension sc

Downloads : 46   Arquivo Tamanho: 2 mb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

SM 2055E TABLE OF CONTENTS Introduction ....................................... 3 Symbols ............................................. 4 Warning Signs ................................... 4 Safety Regulations ............................ 5 Description ........................................ 7 Installation ....................................... 16 Fuel Handling .................................. 21 Starting and Stopping.....................23 Use.................................................

Downloads : 2   Arquivo Tamanho: 2 mb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

Both situations could cause serious injury. • Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. • Never put a chain saw down while the engine is running unless you have it in clear view and the chain brake is on. Switch the engine off before leaving your chain saw for any length of time. Basic cutting t

Downloads : 0   Arquivo Tamanho: 2 mb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

This results in damage to the oil pump, the bar and the chain. • It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature. • In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. 26 – English FUEL HANDLING Fuelling ! WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place h

Downloads : 0   Arquivo Tamanho: 1 mb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

Seek medical attention if you experience physical symptoms that can be related to over exposure to vibrations. Examples of such symptoms are “numbness“, lack of feeling, “tickling“, “pricking“, “pain“, lack of or a reduction in normal strength, changes in the colour of the skin or its surfaces. These symptoms normally appear in the fingers, hands or wrists. 5. Quick-release There is an easily accessible, quick-release catch fitted to the chest as a safety precaution in the event of a fire in the

Downloads : 0   Arquivo Tamanho: 242 kb   Fabricante : Jonsered  
Categoria : Benzo e serras

Downloads : 3   Arquivo Tamanho: 618 kb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

If the cutting attachment still rotates after idle speed adjustment, contact your service workshop. NOTE! The L and H screws should only be adjusted by an Authorized Tanaka Dealer. The standard openings (returns) of L/H screws from lightly seated positions are as follows: WARNING! When the engine is idling the cutting attachment must under no circumstances rotate. NOTE FOR THE US MARKET!! (Fig. 3-1B) We would like to inform that the machines, which carry the following label on the unit are diffe

Downloads : 6   Arquivo Tamanho: 498 kb   Fabricante : Jonsered  
Categoria : Benzo e serras
@name

Q=Quan. used C=lnterchangeability S=Stocking code: A-Fast moving B=Med. fast C=Med. move D=SJow move E=N.L.A. F=Superceded or replaced by a new part FIGURE 2 cont. ECS-655 PARTS LISTING REF. PART NO. PART DESCRIPTION Q C S SERIAL NO REMARKS 44 990-11030-061 SCREW.3X6 2 D 51 992-10050-012 WASHER, S,5 2 A 52 992-10050-062 WASHER,S,5 2 D 53 992-00050-061 WASHER,SMALL,5 3 D * Indicates the part is included in a kit or assembly and is not availiable individually. Q=Quan. used C=





categorias