! WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition. These symptoms normally appear in the fingers, hands or wrists. These symptoms may be increased in cold temperatures. Stop switch Use the stop switch to switch off the

Chain brake and front hand guard Your chain saw is equipped with a chain brake that is designed to stop the chain if you get a kickback.The chain brake reduces the risk of accidents, but only you can prevent them. English – 7 GENERAL SAFETY PRECAUTIONS Take care when using your saw and make sure the kickback zone of the bar never touches any object. • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. A B E •This movement a

NOTE: If chain is difficult to rotate on guide bar or if it binds, too much tension has been applied. This requires minor adjustment as follows: A. Loosen the bar retaining nut so it is finger tight. Decrease tension by turning the bar adjustment screw CLOCKWISE slowly. Move chain back and forth on bar. Continue to adjust until chain rotates freely, but fits snugly. Increase tension by turning bar adjustment screw COUNTERCLOCKWISE. B. When saw chain has proper tension, hold nose of bar in upperm

Start making the upper notch cut (C) on the side of the tree facing the felling direction (E). Be sure you don t make the lower cut too deep into the trunk. The notch (C) should be deep enough to create a hinge (F) of sufficient width and strength. The notch should be wide enough to direct the fall of the tree for as long as possible. OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Fig. 11 LIMBING Limbing a tree is the process of removing the branches from a fallen tree. Do not remove supporting l

1501 SPRING, BRAKE 1 55 MC-6011-211502 POWER CORD 1 21 MC-6073-211501 GEAR 1 56 MC-6043-840001 STRAIN RELIEF 22 MC-6059-210201 ADJUSTMENT COVER 1 57 MC-6059-855001 CORD GUARD 1 23 MC-6115-211502 PIN 1 58 MC-6012-211501 RUBBER STOP 24 MC-6154-211502 CONNECTION 1 59 MC-6024-211506 SPRING 1 25 MC-6CG-9.5 C RING 1 60 MC-6PC05-14.7 PIN 26 MC-6014-210502 WASHER 1 61 MC-6PC4.4-35 PIN 1 27 MC-6228-210104 GEAR BEARING ASS'Y 1 62 MC-6SQAB-04-06 SCREW 28 MC-6077-211501 COVER 1 6

You can check the oil tank level using the inspection slot (D) provided on the right side of the saw. The tank is full when oil is at the top of the slot (Fig. 25). D Fig. 25 Never starve the bar CAUTION: and chain of lubrication oil. Running the saw DRY or with TOO LITTLE OIL will decrease cutting efficiency, shorten chain saw life, and cause rapid dulling of the chain and excessive wear of the bar from overheating. Too little is evidenced by smoke or bar discoloration. NOTE: The saw chain stre

Si el arbol golpea cualquier red de servicio publico, la compania correspondiente debe ser notificada de inmediato. . Siempre corte con ambos pies bien apoyados en suelo solido para evitar perder el equilibrio. . No corte arriba de la altura del hombros, ya que si se tiene la sierra mas arriba de esa altura, es dificil de controlar bajo la fuerza del contragolpe. . No corte arboles cerca de cables electricos o de edificios. Deje tal operacion a los profesionales. . Corte solamente cuando al visi

SPARK PLUG REFERENCE GUIDE 78 F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE SHOP MANUAL USE TITLE SHOP MANUAL USE 613GC SERVICE MANUAL Shop Manual Use This manual contains all the technical information necessary for carrying out repairs on the 613GC cut-off saw. For safe, efficient work, it is of prime importance that the values indicated be adhered to. Routine periodic maintenance is covered in the operator’s manual included with each cut-off saw. General Shop Rules • Always use the right tool

.. 01325 300303 eop.customer.services@electrolux.co.uk 1 1 instruction manual Switch levers blade cover/storage holder Handguard Carton Contents IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this Hedgetrimmer can be dangerous! This Hedgetrimmer can cause serious injury to the

All of the centres listed stock genuine Electrolux Spare Parts. NOTE: Our Service Repairers act on their own behalf and are not empowered to commit or legally bind Electrolux Outdoor Products in any manner whatsoever. Declaration of Conformity I, the undersigned M. Bowden of Electrolux I, the undersigned M. Bowden of Electrolux I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial P