DO NOT FORCE CONNECTORS TOGETHER. LINE UP LOCATING TABS AND CAREFULLY MATE CONNECTORS. INSTALLATION INSTRUCTIONS FOR THE CDC-FDW: (Fig. 1) IMPORTANT : Installation must be done with vehicle and radio in OFF position. 1. Mount the CD Changer at the desired location in the trunk following the installation instructions supplied with the CD Changer. 2. Carefully connect the 8-pin circular DIN connector from the CDC-FDW to the mating socket on the CD Changer. 3. Route the CDC-FDW cable toward the exi

Depending on the application, connect the Black/Green wire to the ground tab on the back of the factory radio chassis or splice wire to Pin #11 of the vehicle side J1 connector. 9. Either by splicing or using the T-tap provided, connect the Grey/Purple wire from the CDC-FDN to Pin #9 wire of the vehicle side J1 connector. OPERATION CHECK: 1. Load CD’s into the CD Changer cartridge and insert the cartridge into the changer. 2. Start vehicle and allow CD Changer to cycle. Perform a brief functiona

7 Setting the Clock ............................................................................. 7 Specifications .................................................................................. 8 Care and Maintenance .................................................................... 9 Warranty .......................................................................................... 10 OPERATING INSTRUCTIONS 1 11111 ON-OFF POWER BUTTON Press this button to turn the unit on or off. 2 22222

Remove factory radio dash panel to expose sub-dash. 2. Remove radio/map pocket assembly from the sub- dash. Retain the factory supplied mounting hardware. 3. Disconnect the factory radio harness and antenna lead. Loosen the radio mounting screws on one side of the radio/map pocket assembly. 4. Remove the pocket attached to the factory radio mounting bracket and discard as it will not be used in conjunction with the CDI-100R. CDI-100R PREPARATION 1. Install the CDI-100R into the bracket assembly

DISC PLAYING 1. Open the CD tray with the OOPENO button. 2. Insert the CD with the printed side facing upwards and push the disc gently unit it clicks so that the disc fits into the pivot. 3. Press the CD door to close. On display windows When you press O O, the display window shows : Total number of tracks First track playing begins During play The track number of the current selection appears. When O O is press during play, total number of tracks on the disc will be displayed and the unit stil

If you Notes: • The normal function of the product reconnect the power source for resume • The CD player and adaptor shall not be exposed filled with liquids, such as vases, shall be placed ON INSTALLATION Never install the unit where it would be subject to: - heat sources such as radiators or airducts. - direct sunlight. - excessive dust. - moisture or rain. - mechanical vibration or shock. - uneven surface. • Do not place any heavy object on top of the unit. • When the unit is used with an AC

• Adjust the volume control • Dirty plug SKIPPING OF SOUND: • Dirty or defective disc • Dirty lens • Strong vibration WHEN USING WITH BATTERIES THE BATTERY LIFE IS SHORT: • Use alkaline batteries and not manganese batteries. DISPLAY WINDOW SHOWS “ ” ERROR MESSAGE AND THE UNIT CANNOT BE OPERATED: • No disc, dirty or scratched disc. The unit will return to power off after approx. 30 seconds, or reset the player by pressing “ ” button once and then insert a disc to start playing. SPECIFICATIONS GEN

The treble level is now pre-set for the current type of broadcast. 4. Repeat step 1, except set the desired bass (BAS) level for the current broadcast and set this level using the VOL / buttons. While BAS is displayed, press and hold the P1 button until P_1 appears to the left of the BAS display. The bass level is now pre-set for the current type of broadcast. 5. Repeat step 1, except set the desired balance (BAL) between the left and right speakers for the current broadcast, and set this level

4. Discs should be put back in their cases after use to avoid serious scratches that could cause the sound to skip. 5. Do not expose discs to direct sunlight, high humidity, or high temperatures for extended periods of time. Long exposure to high temperatures can warp the disc. 6. Do not stick paper, labels, or tape on the disc surface. 7. Do not write with any type of pen, pencil, or marker on the disc surface. 8. To minimize fingerprints and smudges on the signal surface, always try to hold th