2 Press one of the function buttons to select the source to be mixed, and play it. 3 Adjust the volume and tone of the source. 4 Adjust the microphone volume. You can adjust the volume of the microphones connected to the both of the MIC jacks by the MIC MIXING control at the same time. To record microphone sound mixed with source sound Insert a tape in the deck 2, and press the l REC/REC MUTE button. You can record while using the echoing effect, VOCAL FADER, MULTIPLEX or BBE function. When not

To correct the current time+ See illustration q . While pressing the SHIFT button, press the CLOCK button on the remote control. The clock is displayed for 4 seconds. Within this period, start correcting by following steps 1 to 5. To switch display to clock while power is on While pressing the SHIFT button, press the CLOCK button on the remote control. The clock is displayed for 4 seconds. During recording, the clock cannot be displayed. To switch to the 24-hour standard The time display is fact

1 Insert tapes into deck 1 and deck 2. 2 Press the TAPE/DECKl/2 button to select the deck to be played back first. 3 Press the REV MODE button to select 1]. 4 Press the 4 F button to start playback. Playback continues until the n button is pressed. About cassette tapes To prevent accidental erasure, break off the plastic tabs on the cassette tape after recording with a screwdriver or other pointed tool. \ Type II tape Tab for side A detection >ti slot / To record on the tape again, cover the tab

(U model only) This equipment has been tested and found to comply w!th the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These Ilmks are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there IS no guarantee that i

Please refer to them when you contact yourAIWA dealer in case of difficulty. TO REDUCE THE SHOCK, DO NOT RAIN OR MOISTURE, RISK OF FIRE EXPOSE THIS OR ELECTRIC APPLIANCE TO LCX-300 U, K, LH, LCX-301 U 1 I “CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, CAUTION (K model) DO NOT REMOVE COVER (OR BACK). Use of controls or adjustments or performance of procedures NO USER-SERVICEABLE PARTS INSIDE. other than those specified herein may result in hazardous radiation exposure. REFER SERVICING TO QUALIFI

To check the specified time and source Press the TIMER button. The timer-on time, the selected source name and the duration for the timer-activated period are displayed for 4 seconds. To cancel timer standby mode temporarily Press the TIMER button repeatedly so that 0 or OREC disappears on the display. To restore the timer standby mode, press again to display @l or OREC. Using the unit while the timer is set You can use the unit normally after setting the timer. Before ‘turning off the power, re

Recording/ Playback Cotton swab Erasur tan \/ \ I (1.:Q I,JJn .IJ, \ . After cleaning the heads and tape paths with a liquid head cleaning cassette or a moistened swab, wait until the cleaned parts are completely dry before inserting the tapes. To demagnetize the heads The heads may become magnetized after long-term use. This may narrow the output range of recorded tapes and increase noise, After 20 to 30 hours use, demagnetize the heads with any commercially available demagnetizer. Care of disc

Voices are reproduced in the front and center sound field, while ambient sounds like cars and crowds are reproduced on all sides of the listener for an incredibly lifelike audio/video experience. Please read the following carefully to “tune” the system’s output to match the characteristics of your listening space. Check the following: Before using the DOLBY PRO LOGIC, adjust the proper balance of speaker sound levels. Make sure the supplied speakers are properly connected and positioned. (See pa

The skipped track is cleared from the program. To clear all the reservations Press the FP button repeatedly until “K -“ is displayed, Press it once more to cancel the Karaoke programs. The display returns to that of CD play. m If the reserved track number does not exist on the selected disc, the unit stops playing and the display flashes. In this case, press the a> button to skip the error track. Then press the 4 a button to start play with the next reserved track. When the PRGM button is presse

After tuning into a station, the search stops. To stop the Auto Search manually, press 4+ DOWN or UP. The Auto Search may not stop at stations with very weak signals. When an FM stereo broadcast contains noise Press MONO TUNER on the remote control so that “MONO appears on the display. Noise is reduced, although reception is monaural. To restore stereo reception, repeat the above so that “MONO” disappears. To change the AM tuning interval The default setting of the AM tuning interval is 10 kHz/s