• This power unit is intended to be correctly orientated in a vertical or floor mount position. SAVE THESE INSTRUCTIONS INTRODUCTION Black & Decker VPXTM chargers are designed to charge Black & Decker VPXTM battery packs in approximately 5-6 hours. The charger requires no adjustment and is designed to be as easy as possible to operate. Simply place your battery pack into the receptacle of a plugged in charger and it will automatically charge the pack. As you add new chargers to your Black & Deck

When not in use, before servicing; when changing accessories such as blades, bits, cutters, etc. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 18. AVOID ACCIDENTAL STARTING. Don’t carry plugged-in tool with finger on switch. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 14. 15. 16. 17. GROUNDING EVERY ELECTRIC TOOL SHOULD BE GROUNDED while in use,to protect the operator against shock. This uni

Brushes should be regularly inspected for wear if your tool has extfrior brush inspection caps. When the cap is unscrewed, the spring and brush assembly may be withdrawn from the tool, Keep brushes clean and sliding freely in their guides. Inspection should be made every two to six months, depending upon usage, SWITCHES. Pulling the Trigger Switch turns the tool “ON”; releasing the trigger, turns the tool “OFF”, y2" drills have reversing capability. For controlling the rotational direction of

Ailops maximum pressure on drill bits for faster cutting into wood, metal, or masonry. Tools available include y4", y2" drills and Wf heavy duty right angle drill kits for plumbers and electricians. For personal safety and proper operation of End Handle Drills please read all of the Safety Rules and- Instructions in this" booklet Don't forget to send in the Owner Registration- card. THANK YOU for buying BLACK & DECKER! HEAVY DUTY END HANDLE DRILL 14" DRILL %" DRILL if2" DRILL i/2" RIGHT ANGL

To avoid stress on the drill bit, try extending your index finger along the side of the drill-housing with your middle finger on the trigger. Remember—guide, the tool, don't force it! Should the tool become overheated, run it with no load. Because of the drill's construction, it will cool faster running than by stopping it. DULLING IN METAL Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. The cutting lubricants that work best are sulp

Remember— guide, the tool, don't force it! Should the tool become overheated, run it with no load. Because of the drill’s construction, it will cool faster running than by stopping it. DRILLING IN METAL Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil; bacon grease will also serve the purpose. Aluminum is best drilled with turpentine or kerosene. DRILLING I

A built-in mechanical interlock prevents changing the direc-. tion of the tool with the Slide Switch unless the Trigger Switch is released, turning the tool “OFF” during the directional change. After any reversing, return switch to forward position. 4 SWITCHES (Continued) switch locking button and %" drills -have a switch locking button. This button permits locking the trigger in the full “ON” position for continuous operation. To lock trigger in “ON” position depress trigger and push in loc

Never connect this green wire to a “live” terminal. If you replace the plug on the power cord, be sure to connect the green wire only to the grounding (longest) prong on a 3-prong plug. 3 EXTENSION COii When using the tool at a considerable distance from power source,-a 3-conductor, grounding-type extension cord of adequate size must be used for safety, and to prevent loss of power and over-heating. Use the table below to-determine minimum wire size. Use only three wire extension cords which

This insures that the tool will stop.when the'brushes wear out This prevents damage to the motor. Brushes should be regularly inspected for wear if your tool has extfrior brush inspection caps. When the cap is unscrewed, the spring and brush assembly may be withdrawn from the tool, Keep brushes clean and sliding freely in their guides. Inspection should be made every two to six months, depending upon usage, SWITCHES. Pulling the Trigger Switch turns the tool “ON”; releasing the trigger, turns

If you have any questions about your too! please call: 1-800-9-BD TOOL (1-800-923-8665) MULTI-POSITION REVERSING SIDE HANDLE LEVER ■e'-^sCS GEARED «I CHUCK I IJk J® BRUSH «B|| INSPECTION CAP TRIGGERS WITCH RIGHT ANGLE HEAD MULTI-POSITION SIDE HANDLE GEARED_| CHUCK f REVERSING TRIGGERS LEVER WITCH BRUSH INSPECTION CAP^ IMPORTANT SAFETY INSTRUCTION, WARNING: When using electric tools, basic safety precautions sh always be followed to reduce risk of fire, electric shock, and pe