If an adapter is used to accommodate a two-prong receptacle, the adapter lug must be attached to a known ground. Never remove the third prong. 5. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it "on." 6. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 7. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations, or expose them to rain. Keep work area well-lighted

SPINDLE SPEEDS Twelve spindle speeds are available on the drill press. Fig. 23, illustrates the speeds and which steps of the pulleys the belts must be positioned to obtain the 12 speeds. Fig. 21 Fig. 22 SPINDLE CENTER MOTOR 540 360 250 1090 590 410 1820 1280 650 3000 2180 1450 Fig. 23 11 CHANGING SPINDLE SPEEDS AND ADJUSTING BELT TENSION 1. DISCONNECT THE DRILL PRESS FROM THE POWER SOURCE. 2. Raise the belt and pulley guard (A) Fig. 24. 3. Release tension on the belt by loosening lock knob (B)

No adapter is available or should be used when the drill press is converted for 230 volts. If the drill press must be reconnected for use on a different type of electrical circuit, the re-connection should be made by qualified service personnel; and after re-connection, the tool should comply with all local codes and ordinances. GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES Fig. C 6 1 234 5 6 7 8 9 10 11A 11B 12 13 14 15 16 17 18 1 234 5 6 7 8 9 10 11A 11

ADJUSTING SPINDLE RETURN SPRING The spindle will automatically return to its upper-most position when the handle is released. Allow the handle to return slowly to the top position after each hole has been drilled. This spindle-return spring was adjusted at the factory. However, to adjust (if necessary): Disconnect the machine from the power source! 1. Loosen the nuts (B) and (E) Fig. 30. Make sure that the spring housing (A) stays engaged with the head casting. 2. FIRMLY HOLD the spring housing

Make certain that the bottom of the raising rack (F) Fig. 8 is engaged with the flange (K) on the drill press base. FI Fig. 7 F J 9 10 5. Re-install the ring (E) Fig. 9 (removed in STEP 1). IMPORTANT: DO NOT push the ring (E) Fig. 9 all the way down on the the raising rack (F). Make certain that the top of the raising rack (F) is under the bottom of the ring (E) and that enough clearance is available to allow the rack (F) to rotate around the column. Tighten the set screw (D) with the supplied 3

LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. CROSSHAIR OBJETIVO CRUZ CIBLE CROISEE 18-900L TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ..........................2 SAFETY GUIDELINES - DEFINITIONS ...........................2 GENERAL SAFETY RULES .............................................3 ADDITIONAL SPECIFIC SAFETY RULES ......................4 ADDITIONAL SAFETY RULES FOR THE LASERS ........4 FUNCTIONAL DESCRIPTION .........................................6 CARTON CO

20-950 20-950 20" Floor Model Drill Press La perceuse a colonne de 508 mm (20 po) Prensa de taladro de 508 mm (20”), modelo de apoyo sobre el suelo 223-7278 - US (800) 463-3582 - CANADA Instruction Manual Manuel d’Utilisation Manual de Instrucciones FRANCAIS (21) ESPANOL (39) A20334_12-05-06 Copyright © 2006 Delta Machinery TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ....................2 SAFETY GUIDELINES - DEFINITIONS .....................3 GENERAL SAFETY RULES ..........

or less in diameter. The following directions will give the inexperienced operator a start on common drill press operations. Use scrap material for practice to get a feel of the machine before attempting regular work. IMPORTANT: When the workpiece is long enough, it should always be positioned on the table with one end against the column, as shown in Fig. 32. This prevents the workpiece from rotating with the drill bit or cutting tool, causing damage to the workpiece or personal injury to the op

SPINDLE SPEEDS Five spindle speeds of 620, 1100, 1720, 2340 and 3100 RPM are available with your drill press. The highest speed is obtained when the belt is on the largest step of the motor pulley and the smallest step of the spindle pulley, as shown in Fig. 25. Fig. 25, illustrates which step of the motor and spindle pulley the belt must be placed to obtain the five speeds available. B D Fig. 22 E F Fig. 23 SPINDLE MOTOR 3100 2340 1720 1100 620 Fig. 25 10 A B D C E A B D C E Fig. 27 CHANGING SP

20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. 21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. 22. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE WHEN OPERATING A POWER TOOL. DO NOT USE TOOL WHILE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power tools may result in serious personal injury. 23.