Log:
Downloads : 1   Arquivo Tamanho: 322 kb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

Do not leave a battery charging for longer than 24 hours. 1. Align and slide the slim line adaptor (9) onto the battery until the battery pack latches “click” into position. Check the adaptor is flush with the battery and there is a firm connection. 2. Connect the power supply from the charger to the slim line adaptor via the socket in the rear of the adaptor housing. 3. Plug in the charger and switch on. The red LED indicator will show power to the adaptor and that charging is taking place. 4.

Downloads : 5   Arquivo Tamanho: 1 mb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

Downloads : 0   Arquivo Tamanho: 322 kb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

There are 3 levels of charge low, medium and high. When the battery indicator is showing only 1 LED (low) the battery should be removed and put on the charger. LED Work area light The drill has 3 LED lights (11) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on and off depress the LED light switch (13). Using the drill Use the forward/reverse switch (4) to select the direction of rotation, then pull the trigger (3). This trig

Downloads : 0   Arquivo Tamanho: 40 kb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

You will hear a click as the clips engage. 3. Fully push the drawer into the case. Global Machinery Company 16 Scammel Street, Campbellfield Victoria, Australia 3061 Tel: (03) 9303 2133 Fax: (03) 9308 7822 Customer Helpline 1300 880 001 (Australia) 0800 445 721 (New Zealand) 300PCE 030117 300PCE EDS

Downloads : 0   Arquivo Tamanho: 2 mb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

Position battery pack on charger; align rails (d), on battery charger with (e) on battery pack. Slide battery forward onto charger until it clicks into position. The red light (b), should begin to glow continuously, indicating that the battery pack is receiving a “Fast Charge”. Note. If the red light does not glow continuously, but the yellow light is flashing and the green light (c), begins to glow, remove battery and re-insert when battery temperature is between 0°C and 40°C. After approximate

Downloads : 1   Arquivo Tamanho: 2 mb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

Downloads : 1   Arquivo Tamanho: 2 mb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

The switch is equipped with a brake, the chuck will stop as soon as the trigger switch is fully released. To stop the drill, release the trigger switch. Forward/Reverse control The forward/reverse control (4) allows you to change the direction of the tool while the variable speed trigger is not depressed. To select forward rotation depress the control (4) toward the left side of the tool. To select reverse depress the control (4) to the right side of the tool. Drilling uses the forward mode. The

Downloads : 0   Arquivo Tamanho: 2 mb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

This is important. Failure to observe this safety rule could cause serious damage to the battery pack. • Do not incinerate the battery pack even if it is seriously damaged or can no longer hold a charge. The battery pack can explode in a fire. • Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks open or cracks, immediately discontinue its use and do not recharge it. • The battery pack utilizes nickel-cadmium cells. Cadmium is considered to be

Downloads : 1   Arquivo Tamanho: 2 mb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

If found to be defective in materials or workmanship, the tool or the offending faulty component will be repaired or replaced free of charge with another of the same item. A small freight charge may apply. Proof of purchase is essential. We reserve the right to reject any claim where the purchase cannot be verified. This warranty does not include damage or defects to the tool caused by or resulting from abuse, accidents, alterations or commercial or business use. It also does not cover any bonus

Downloads : 0   Arquivo Tamanho: 2 mb   Fabricante : Global Machinery Company  
Categoria : Brocas e shuropopverty
@name

Tighten the chuck around the shorter end of a hex key (not supplied) of 5mm or greater size. Using a wooden mallet or similar object, strike the longer end in the clockwise direction. This will loosen the screw inside the chuck. 1. Open chuck jaws fully. 2. Insert a 5mm hex key into front of chuck between jaws to engage screw head. Remove screw by turning clockwise. 3. Place the hex key in chuck and tighten. Using a wooden mallet or similar object, strike key sharply in the anti-clockwise direct





categorias