Instruction Manual RCWL300A Premium Portable Wireless Chime & Push 69-2109EFS-05 Installation Instructions 69-2109EFS—05 ii Contents Checking pack contents.............................1 Safety...........................................................2 Quick start...................................................2 Open bell push............................................3 Fit the push battery....................................3 Fit the chime battery...................................4 Sliding

MESSAGE CENTER TO: PRESS: Record a message: # + 1 Stop recording before end of 20 seconds: 1 Playback a message: # + 3 Adjust message playback volume: # + 2 + 39 or 6. Mute keypad status announcements: # + 2 + 1 Restore keypad status announcements: # + 2 + 39 or 6. New message indication: If powered by battery, the Message LED will only blink when you activate the keypad by requesting status. If powered by AC, the Message LED will blink continuously. Once the message is played back, the LED will

This device operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment. Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden

Illuminated bell push buttons can be used when the chime is powered by a transformer (Honeywell RCA900N). Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. • Chim

Follow manufacturers’ advice on the paint/vanish. It is possible to unscrew the four screws shown below for painting. Ensure you screw it back with the same screws provided! Once completed, clip it onto the base as in step 11. Installation Specification Chime Bell push Operating Temperature 32°F to 104°F 0.C to 40.C 14°F to 104°F -10.C to 40.C RF Frequency- US 916.8 MHz 916.8 MHz Range (open field) 450 ft. (140 m) Sound Level (typical) 90dBA @ 3 ft. (1 m) - RF Power - <1mW Battery Type LR14 (C s

Note the + and - symbols molded into the back of the battery compartment. • If the chime sound becomes faint or distorted, you should replace the batteries. Use LR14(C) alkaline batteries only. • Check that the push battery has enough charge and is installed the right way. Note the + and - symbols molded into the back of the battery compartment. • Check that the bell push channel switch and the chime channel switch are in the same position. See Set Up. • Check that the distance between the bell

Taladre un agujero en la pared, en el lugar donde desea colgar la campanilla. Si la esta instalando en una pared de mamposteria, utilice el tarugo de pared incluido. 2. Inserte el tarugo de pared en el agujero (si es necesario), luego atornille dejando la cabeza sobresaliendo 6 mm de la superficie. 3. Cuelgue la campanilla de modo que la cabeza del tornillo quede asentada en el agujero de la parte posterior (F), luego presione suavemente hacia abajo para que la campanilla no pueda deslizarse fue

(Model No. RPWL30XXX series, and RCA901N and RCA902N.) Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. Decorative Wire Free Chimes and Push Checking Pack Conten

Keep these notes in a safe place for future reference. Checking Pack Contents Unpack your chime kit and identify the following parts: •Chime • Wall mounting bracket • Bell push • Bell push/converter/extender • Door contacts • 2x CR2032 battery for bell push and converter • 4x mounting screws for door contacts • 4x mounting screws for push/converter • 2x mounting screws for chime • 2x wall anchors • 2x adhesive pads • Bell wire (for use with converter and door contact) • Self-adhesive icons You w