• Battery powered push button -No wires to run. • 128selectablecodesallowmorethanonechime system in the same house. © 2007 598-1077-02 Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 1. Install alkaline type A2

Your Heath®/Zenith Chime Extender allows you to add doorbell coverage to any room in your house without the need to run additional wires.The Chime Extender "listens" for your existing doorbell to ring, then transmits a radio frequency signal to the plug-in chme unit in another part of the house. 1. Set the chime volume on the back of the plug-in chime, if desired. 2. Plug-in the doorbell chime. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than t

Be careful when opening.DOnOtover extend the front door when opening or damage to hinges may occur. Pull From Here to Open CHiME installatiOn IMPORTANT: Proper installation requires a diode on the front door push button. See Diode Installation Instructions (page 5) after completing steps 1 through 10 below. Note: Electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualified electrician. 1. Verify transformer power rating. Power must be supplied

The chime cover style will determine orientation. 7. A cover pin is installed on two sides of the chime base. After determining correct orientation, remove, turn over, and reinstall the cover pin located on top of chime base (see Figure 1). Illustrations may vary from actual chime unit. Figure 1 - Electronic Chime Identification (2300 Base Shown) Cover Pin Volume Control Base Orientation Marking Wire Entrance Hole Front Door Tune Selection Switch (3 Selections or 10 Selections – Depending on Mod

(Volume control feature is available on selected chimes). 2.Testrange.Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. WirelessPlug-InChimeAccessoryReceiverModel3106978(AC-6196) This package includes (Style of chime may vary from illustration): • Wireless chime • Hardware pack Chime Volume Control (Depending upon model) Access Door 3.Setchimevolume.Locate control on back of plug-in chime. (Volume control feature is available on select

Note: If batteries are preinstalled, remove orange battery tab. 2. Remove chime cover. Use a small screwdriver to pry the cover tabs away from chime base and remove cover (see Figure 2). Note: To remove the cover after base is mounted, firmly grasp cover and pull. 3. Install 3 alkaline “D” batteries. Make sure batteries are oriented properly (see Figure 3). Chime Cover Tab (x4) Horizontal Keyhole Vertical Keyhole Mounting Holes Figure 2 - Back of Chime Type “D”Type “D”Type “D” Chime Volume Chime

In typical use, alkaline batteries will last up to three years. Battery Chime Volume 1. To open the chime case: press in the catch on the bottom of the chime and lift the case open. 2. Install the 3 alkaline "D" batteries. Make sure the batteries are oriented properly. 3. Before mounting, test the doorbell range. Put the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Operation Press the doorbell button to verify that the doo

1. Verify transformer power rating. Power must be supplied from a 16 Volt AC, 10 Watt or a 16 Volt AC, 15 Watt transformer (Heath®/Zenith models 122C, 121AC, or 125C). 2. Remove cover from existing chime. 3. Label all wires before disconnecting. Using masking tape, mark each wire according to existing chime terminal markings. • “F” – Front Push Button Wire • “T” – Transformer Wire • “R” – Rear Push Button Wire* 4. Disconnect all wires from existing chime. 5. Remove existing chime base from wall.

Sound travels farthest with the fewest obstacles. Do not place over heat source; i.e., radiator, heater, or stove. At the chosen location drill two small pilot holes 3 1/4" apart in the vertical plane. The chime cover is a push fit onto the base. Remove chime cover to expose base. Position base and mount in place using screws supplied, key-hole shaped slot at the 1 32 Base Plate Chime Cover top (see Figure 1). Figure 1 WIRING THE CHIME To Push Button A. Battery Operation. Do not use with lighted

Snap the front of the button back on. When attaching the doorbell button using the double sided tape, make sure the surface of the door jamb or wall is clean. © 2003 DESA Specialty Products™ 595-5707-04 The chime can be mounted by using the 3 holes in the back of the case, or by using 2 screws with the keyholes. Chime Back Case Keyhole Mounting Chime Back Case Mounting Close Chime Case From Bottom Snap the front of the chime case back on. Start with the bottom edge of the case aligned wi