Assessments - 3, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Use a tripod or place the camera on a stable flat surface. The controllable distance of the remote control is within approx. 5m while facing the camera. If the camera-to-subject distance is more than 5m away, use the self-timer. Remote Control mode will be automatically canceled if the camera is not operated for more than approx. 3 minutes or when the slide cover is closed. En 3150mmMacrNikonZoomLensED 2 Compose the picture, aim the remote control at the camera, and press the transmission button on the remote control. The self-timer lamp lights up for approx. 2 seconds before the shutter is released. Within 3 minutes after taking the last shot using the remote control, you can still continue to shoot by remote control. Remote control operation cannot be performed when the camera has extreme backlighting. Change the camera position in this case. The life of the battery in the remote control is approx. 5 years. If the battery is exhausted, the shutter may not be released with the remote control. Replace the battery inside the remote control with a new one. ( p. 40) Advanced Operations 39 Replacing the remote control battery 1 While keeping the battery holder release lever pressed as the arrow on the remote control indicates to release the lock 1, pull out the battery holder from the remote control 2. 2 Replace the battery. Use one 3 V lithium (CR2025 type) battery. Insert the battery with + polarity side facing up into the battery holder. 3 Insert the battery holder into the remote control until it clicks closed. Warning: Keep the batteries out of the reach of children. If a battery is swallowed, consult a doctor immediately. 40 Advanced Operations Correcting the date and time (Lite Touch Zoom 150ED QD only) ADJ button MODE/SEL button 1 Press and hold the MODE/SEL button for more than 2 seconds. When the date/time display format is Year/Month/Day, Month/Day/Year, or Day/Month/Year, “Year” indicator flashes first. For Day/Hour/Minute display, “Hour” indicator flashes first. The date/time correction can be performed with the camera either on or off. When the camera is on, the data will be immediately registered if the slide cover is closed, or the Mid-roll Rewind button or a Zoom button is pressed while the setting is in progress. 2 Press the ADJ button to set the flashing digit. Each time you press the ADJ button, the number advances by one. Holding the ADJ button pressed for more than 2 seconds advances the number quickly. 3 When the flashing indicator is correctly set, press the MODE/SEL button again so that the next indicator flashes. Repeat steps 2 and 3 to set all the digits. When the Year/Month/Day or Day/Hour/Minute have been adjusted, press the MODE/SEL button to finish the adjustment procedure. If the Year/Month/Day or Day/Hour/ Minute are all displayed correctly, adjustments has been completed. En When the battery is replaced aThe LCD panel shows “ ”. aThe date/time is not imprinted in pictures taken while “ ” is indicated. Set the date and time following the above procedure. aIf the battery is replaced immediately, the date and time previously set remain in memory and you do not need to set again. Additional Information 41 Troubleshooting Track down the cause of trouble using the following chart. It may save you a trip to your nearest Nikon service center. Problem Check points and solution Ref. page a The slide cover is not completely open. > Open the slide cover all the way until it clicks to turn the camera on. a The orange LED flashes. 15 > The flash is charging. Release the shutter after the orange LED lights up. a “ ” lights up on the LCD panel. 13,29 ShutterThe shutter cannot be released. > A rewound roll of film is inside. Replace it with a new roll. a No indicator on the LCD panel. 16,17, 25 > The battery is exhausted. Replace it with a new one.* a All indicators on the LCD panel flash. 14,15 > The camera has detected a malfunction. Once open the slide cover and close it again, then the power is turned on. If the camera still does not work properly, remove the battery from the camera and confirm the indicators turns off, then Install the battery in place again.* 14,15 a The orange LED flashes. > The flash is charging . Release the shutter after the orange LED lights up. a “ ” lights up on the LCD panel. 13,29 FlashThe flash does not fire. > The flash does not fire when the subject is bright enough. To fire the flash, set the camera to the Anytime Flash mode. a No indicator, or the “ ” flashes or lights on 30,32 the LCD panel. > Battery power is low or the battery is exhausted. Replace the battery with a new one.* a The orange LED is flashing quickly (at 8 Hz). 14,15 > Check that the flash unit is not pressed down. Do not touch the flash unit. 13,29 42 Additional Information Problem Check points and solution Ref. page a Camera shake. >Gently press the Shutter Release button, or use a 20,31, The subject tripod or place the camera on a stable flat surface. a Something in front or behind the sub...