101 89 75-26 Symbols WARNING! The edger can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator's Manual carefully and understand the content before using the machine. Always use: • A protective helmet where there is a risk of falling objects. • Ear protection • Approved eye protection • Max. speed of output axle, rpm • This product is in accordance with applicable CE directives. • Beware of thrown objects and ricoche

960 73 00-03 54 Inch Mower Grass Catcher 03056 SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent ac- cidental starting when setting up, transporting, ad justing or making re- pairs, al ways dis connect spark plug wire and place wire where it can not contact spark plug. WARNI

Make sure the throttle control is locked at the idle setting when the throttle lock is released. Press the throttle lock and make sure it returns to its original position when you release it. Check that the throttle control and throttle lock move freely and that the return springs work properly. See instructions under the heading Start. Start the machine and apply full throttle. Release the throttle and check that the sweeper rollers stops and remains at a standstill. If the sweeper rollers rota

WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. US-1 BP5 SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the sprayer concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. Note that there may be times when warning se

01 (03/13/06) 2 ©2003 Husqvarna. All Rights Reserved. Beatrice, NE. Printed in U.S.A. CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/ department. They have competent, well-trained technicians and the proper tools to service or repair this mower. Please read and ret

Discard the support flange if it is cracked. • Ensure that the nut has not lost its tightening capacity. The nut lock shall have a locking torque of at least l.5 Nm. The nut’s tightening torque shall be 35-50 Nm. • Check that the blade and blade guard are not damaged or cracked. Replace the blade or blade guard if it has been exposed to impact or if it is cracked. 8 – English English – 9 Lubricating the flexible drive axle Inside the edger‘s drive shaft is a flexible drive axle. The flexible dri

Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out. Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty. ! WARNING! Mufflers fitted with catalytic convert

540200239 REV. 12/11/00 Lawn Aerators Index Section 1 · Operator’s Guide Page Specifications .......................................................................................................................... 3 Features and Controls ............................................................................................................ 4 General Information ................................................................................................................ 7 Safety Procedu

(B) Use the rear wheel depth/stability control knob to set the rear wheels for extra stability. This can be a great benefit when you do choose to run the aerator across a hill. An added benefit of using the rear wheel depth control when aerating across a hill is that you will improve the consistency of the cores pulled from the uphill tines when compared to those pulled by the downhill tines. (C) Removing the downhill weight reduces roll-over risk and maintains consistent core plug length. (See

Siehe Bild 5. 8. Die Schrauben (J) durch das Unterteil des Wagens und die Befestigungsbeschläge anbringen. Sicherungsscheiben (K) und Muttern (L) montieren. Nur diese leicht anziehen (die Schrauben werden von der Innenseite des Wagens montiert). Siehe Bild 5. 9. Die Beschläge (S) an die Rückwand montieren, so daß die Bohrungen parallel zur Rückwandverstärkung und den Wagenseiten laufen. Siehe Bild 5 zur genaueren Information. 10. Mit 6 Sechskantschrauben (F), Sicherungsscheiben (H) und Mutter