After you read the warranty, ask your dealer to explain any points that you may not understand. This tractor was designed to power and propel itself. It is intended for use in normal and customary agricultural applications. Do not modify or alter or permit anyone else to modify or alter this tractor or any of its components or any tractor function without first consulting an authorized Buhler Versatile dealer. If you have any questions regarding tractor modifications, contact Buhler Versatile In

TURN SIGNALS Move the stalk to position 1 to indicate a right-hand turn. Move the stalk to position 4 to indicate a left-hand turn. The turn signal warning light (and trailer lights, if connected) will also flash when the signals are operated. HEADLIGHTS HIGH/LOW BEAMS With the headlights switched on, pull the stalk to position 3, to change from one beam to the other beam. HEADLIGHT FLASH With low beam headlights on, pull the stalk to position 2, to flash the high beams. Release the stalk to ret

4. Insert hitch pin and be sure the retainer is in the latched position. NOTE: For implements that require hitch extensions or interfere with the tractor clevis, remove and store the clevis and hitch pin. Always use a safety chain installed between the tractor and implement hitch when transporting equipment on the highway. North American standards recommend that you observe the following precautions for towing equipment not equipped with brakes: DO NOT TOW equipment weighing more than twice the

18. Fill the cooling system with a 50/50 blend of low silicate antifreeze and clean soft water. Add coolant slowly through the radiator filler neck until the coolant is to the bottom of the filler neck. NOTE: To avoid trapping air in the system, fill the radiator as slowly as practicable thereby allowing any air pockets to disperse. 3-59 SECTION 3 -LUBRICATION AND MAINTENANCE EVERY 2400 HOURS OR 24 MONTHS (WHICHEVER OCCURS FIRST) 19. Fill the coolant recovery tank, 1, to the lowest mark, 2. 20.

The “+/–(SET)” button, 2, adjusts the cruise setting. When cruise mode is activated, the engine returns to the last cruise setting, if possible, based on throttle lever position. The cruise function can be set to any engine RPM, but the operating cruise RPM cannot exceed the normal RPM for the current throttle position. For example, if the cruise setting is 1800 RPM but the hand throttle is at a normal 1700 RPM position, cruise will not increase the RPM. On the 2360/2425 models equipped with the

The operator has the option of enabling the feature at any time. If the operator desires to enable the external automatic shutdown feature, proceed as follows: 1. Unhook the battery cables from the batteries. This will prevent any possibility of an accidental short while making the conversion. See Section 3 in this manual for information on how to disconnect the cables. NOTE: Disconnecting the batteries will not remove any calibration numbers from the memory of the Electronic Instrument Control

Examples of electrical faults that can cause the red lamp to illuminate are (but not limited to): - --Failure of the internal microprocessor of the module - --High/Low voltage signal from the throttle POT inside the tractor cab - --Loss of engine speed signal into the module 1 Figure2-124 2-92 SECTION 2 -OPERATION The module will illuminate the appropriate engine warning light (yellow or red) based on the source of the fault, and will take additional action by adjusting the performance of the en

Using diesel fuel with sulphur content above 0.50% requires more frequent oil changes as noted in the maintenance schedule. The use of diesel fuel with a sulphur content above 1.3% is not recommended. Diesel Fuel Selection Chart Do not use Number 2-D fuel at temperatures below -7°C(20°F). The cold temperatures will cause Number 2-D fuel to thicken, which may keep the engine from running. (If this happens, contact your Buhler Versatile dealer.) For the best fuel economy, use Number 2-D whenever t

Malfunctioning fuel injector(s). Malfunctioning fuel solenoid or solenoid relay. Clogged air filter. Review starting procedures. Check fuel level. Bleed fuel system. Use correct viscosity oil. Use correct type fuel for temperature conditions. Clean system. Replace filter element. Contact Buhler Versatile dealer. Contact Buhler Versatile dealer. Clean or replace air filter. Engine runs rough and/or stalls Clogged fuel filter. Clogged air filter. Engine cylinder temperature too low for clean fuel

9Transmission Quadshift gear ranges -All Models Powershift gear ranges -Models 435, 485, 535 48101214162618202224MPHGEAR48101214162618202224MPHGEAR48101214162618202224MPHGEAR LOW RANGE MEDIUM RANGE HIGH RANGE 1 2 3 4 5 6 7 8 9 10 11 12 LOW RANGE MEDIUM RANGE HIGH RANGE 1 2 3 4 5 6 7 8 9 10 11 12 engine speed for peak horsepower and torque, or for constant PTO operation. The next field Farms have expanded and moving to the next field is no longer as simple as crossing the road. With that in mind,