Wash filter assembly in clean fuel and inspect for damage. Note: It is not necessary to remove filter from filter assembly on Model T70. On Model T115 and T165 assembly is one piece. 5. Install filter assembly and bushing (Model T70) into fuel tank. IMPORTANT: Be sure filter (Model T115 and T165) and bushing (Model T70) are firmly seated in tank. 6. Connect fuel line and install side cover. Model T70 B C A Model T115 and T165 C A B 107351-01 19 Periodic Service STORAGE LOCATION AND MAINTENANCE N

It has only information you need for normal operation and maintenance. If a technical manual is desired, see your John Deere dealer for the correct manual. USING SERVICE RECORDS 1. Keep a record of the number of hours or operation. 2. Check your record regularly to learn when service is required. 3. Do all the services in the interval section. Then write the number of hours (from your service record) and the date in the spaces provided. Sample Service Record Chart Date Hours 1 Jun '85 3 6 Jun '8

6. Replace fuse cover. 7. Replace side cover. B C A CLEANING FAN CAUTION: Fan blades are sharp. Carefully work around blades or wear gloves when cleaning. IMPORTANT: Remove fan from motor shaft before removing motor from heater. The weight of the motor resting on the fan could damage the fan pitch. 1. Remove upper shell and fan guard. 2. Loosen setscrew (A) which holds fan (B) to motor shaft (C). 3. Slip fan off motor shaft. 4. Clean fan using a soft cloth moistened with kerosene or solvent. 5.

If more than one heater is used, include equivalent ventilating area. • Provide adequate clearance from people, animals, and combustible materials - 8 feet (2.4 m) from heater outlet; 6 feet (1.8 m) from top; 4 feet (1.2 m) from sides. • Be sure there is no obstruction in intake or output openings. • Be sure heater is on a level, stable surface. • Depending on thermostat setting, heater can start immediately when power cord is connected. • Be sure electrical circuit is adequate and properly grou

Install heater assembly (A) to wheel support frame (B). Align holes in heater assembly and wheel support frame. Note:Wheels are to be at hot air outlet end of heater on T70 ONLY (see next picture below). 2. Install fuel gauge cap (C). A C B 3. Install rear handle (A) using screws (B) and lock nuts (C). DO NOT TIGHTEN. Model T70 Shown A B C 4. Install front handle (A) (excluding T70) using screw (B) and lock nuts (C) DO NOT TIGHTEN. 5. Tighten all screws and nuts. B A C 107351-01 23 Specification

Be prepared if a fire starts. INSPECT SPACE HEATER Be sure all covers, guards and shields are tight and in place. Locate all operating controls and safety labels. Inspect power cord for damage before using. There is a hazard of electrical shock from crushing, cutting or heat damage. Remove all packing items applied to space heater for shipment. Remove all items from carton. Check items for any shipping damage. If space heater is damaged, promptly inform dealer where you bought space heater. SERV

Failure to do so could result in personal injury or equipment damage. This manual and safety signs on your machine may also be available in other languages. (See your John Deere dealer to order.) THIS MANUAL SHOULD BE CONSIDERED a permanent part of your machine and should remain with the machine when you sell it. MEASUREMENTS in this manual are given in both metric and customary U.S. unit equivalents. Use only correct replacement parts and fasteners. Metric and inch fasteners may require a speci

5) .075 inch (Fig. 6) Operator’s Manual Service 6. Remove pressure gauge. Replace pressure gauge plug (Fig. 9) in fuel pump port marked “GAUGE.” PUMP: (Procedure if Pump is Binding) 1. Remove upper shell (Maintenance: Upper Shell Removal). 2. Loosen hex screw on flange clamp at rear of motor with 5/16" nut-driver (Fig. 9). 3. Turn fan with hand (Fig. 10). 4. If fan turns freely, tighten screw on flange clamp. 5. If fan does not turn freely, replace pump. NOZZLE: 1. Remove upper shell. (see Mante

Gal. / Liters) 5 / 18.9 9 / 34 13.5 / 51 Fuel Consumption (Gal. Per Hr / Liters Per Hr) .52 / 1.97 .85 / 3.00 1.2 / 4.54 Pump Pressure (psi) 4.7 5.1 5.6 Electric Requirements 120V / 60 HZ 120V / 60 HZ 120V / 60 HZ Amperage (Normal Run) 2.8 3.6 3.6 Motor RPM 3440 3400 3400 Hot Air Output (CFM) 360 490 575 Motor HP 1/8 1/5 1/5 Shipping Weight (Approximate Pounds / Kilograms) 36 / 16.3 56 / 25.4 71 / 32.2 Space heater Weight without Fuel (Approximate Pounds / Kilograms) 32 / 14.5 48 / 21.8 61 / 27.

7. Keep space heater area clear and free from combustible materials, gasoline, paint thinner and other flammable vapors and liquids. 8. Never use space heater in living or sleeping areas. 9. Never leave a space heater plugged in without adult supervision if children or animals are likely to be present. Do not leave heater unattended. 10. Never move, handle or service a hot or operating heater. Severe burns may result. You must wait 15 minutes after turning heater off. WARNINGWARNINGSINTHEMANUALS