Assessments - , GPA: ( )

Instruções de Operação Quadra-Fire, Modelo PELLET INSERT CB1200MI-MBK

Fabricante : Quadra-Fire
Arquivo Tamanho: 5.44 mb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

Place existing screw head (installed in Figure 23.2) into locator hole in floor of insert. Figure 23.2. 6. Lift hopper lid and press down on panel top while installing (4) 8-32 x 3/8 inch screws into holes in panel support. (If screws have been factory installed, tighten to secure panel to panel support.) Return hopper lid to closed position. 7. Install a corner bracket on each side trim piece. Slide brackets into top trim from each side and secure with flathead screwdriver. Attach trim assembly to panel set as follows: a. Ensure that brackets face towards the back. b. Align trim assembly to panel set sides and slide down. Figure 23.1 Panel Locator Hole Figure 23.3 View of "L" Bracket installed Figure 23.4 Figure 23.5- Completed View Figure 23.2 February 3, 2010 7014-188B Page 23 CB1200-I Pellet Insert R G. Optional Brick Set Installation 1. Slide bottom of left rear brick in first; rotate top edge toward rear of appliance and then rotate outer edge toward rear of appliance, until brick slides into place. Figure 24.1. Repeat for right rear brick. 2. Place left side brick along left side of firebox, making sure chamfered (beveled) back edge fits snugly next to left rear brick. Figure 24.2. Repeat with right side brick. 3. Complete brick set, correctly installed. Figure 24.4. 1 Figure 24.1 • Brick may have small wires protruding from the back of brick. WARNING Risk of Injury. H. Brick Clip Installation 1. After the brick set has been installed, 2 brick clips need to be installed on the outer edge of baffle to keep the brick set in place. Remove the baffles from the appliance before installing the brick clips. 2. Using pliers, bend the brick clip slightly past 90° in the direction shown in Figure 24.4. 3. Position the brick clip as shown in Figure 24.4 and use pliers to crimp around the outside edge of the baffle. Figure 24.5 shows the finished shape of the brick clip after being bent around the outside edge of the baffle. 4. Slide the baffles back into place making sure that the brick clip holds the brick out toward the wall of the firebox. Push back on the sides so they keep the rear bricks in place. Repeat for the opposite side. 123Figure 24.2 Figure 24.4 Approximately 1 inch Top outside corner of Baffle Outside edge of Baffle Brick Clip 1234Figure 24.3 Installed Clip Figure 24.5 Page 24 7014-188B February 3, 2010 RR R RR R CB1200-I Pellet Insert I. Optional Log Set Placement Instructions J. Thermostat Installation CAUTION Logs are FRAGILE. Use extreme care when handling or cleaning logs. 1. A 12 volt AC thermostat is required to operate this pellet appliance. You may use the included wall mount thermostat or purchase an optional programmable thermostat or remote control. The included thermostat is equipped with an adjustable heat anticipator. The current rating is 1. Place the front log in first as shown in Figure 25.1 .05 amps. The anticipator needs to be adjusted to the charred area surrounding firepot. lowest setting available. 2. When mounting a thermostat on a wall, be sure to follow 2. Set the left and right logs onto the front log, placing your thermostat installation instructions carefully. the holes in the base of the left and right logs over the NOTE: Thermostat must be mounted level for accu locating pins in the front log. See Figure 25.2. Ensure rate readings. The thermostat should be mounted on that the charred ends are facing the firepot. an inside wall and not in direct line with the appliance convection air. Remove any packaging from inside the thermostat before using. NOTE: If the thermostat is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired temperature in your home. 3. Open right side plane to access a 4 screw terminal block located on the bottom right hand side next to the power cord inlet. The center 2 screws are for the thermostat wires. The outer 2 are the mounting screws for the terminal block. Figure 25.3. LOCATING PINS Figure 25.1 NOTE: Due to the abrasive nature of a pellet appliance fire, the logs are not covered under warranty. Any placement vari- ation other than shown here can cause excessive heat and shall void the appliance warranty. Charred Areas in the Back Top Log Right Top Log, Left Front Log Figure 25.2 CAUTION Shock hazard. • Do NOT remove grounding prong from plug. • Plug directly into properly grounded 3 prong receptacle. • Route cord away from appliance. • Do NOT route cord under or in front of appliance. Terminal Block Center 2 Screws for Thermostat Wires Power Outlet Figure 25.3 February 3, 2010 7014-188B Page 25 CB1200-I Pellet Insert 8Operating Instructions R A. Fuel Size, Material and Storage 1. Wood Pellets Fuel pellets are made from sawdust or wood by-products. If the source material is hardwood, they can have a higher mineral content, creating more ash. Fuels containing bark will also have higher ash content. Minerals and other noncombustible materials such as sand will turn into a hard,...