Log:
Downloads : 8   Arquivo Tamanho: 15 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

Refer to Section 4.3.2, “Verifying Hardware Operation” on page 4-9 for more information. Chapter 6 Storage Devices Replacement 6-33 6-34 SPARC Enterprise M4000/M5000 Servers Service Manual • December 2010 CHAPTER 7 Power Systems Replacement This chapter describes the power supply units and how to remove and replace them. This information is organized into the following topic: ¦ Section 7.1, “Power Supply Unit Replacement” on page 7-1 7.1 Power Supply Unit Replacement Power supply units are hot,

Downloads : 2   Arquivo Tamanho: 12 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

1 1 ni 1 e Caution — The latch is not an ejector. Do not bend the latch too far to the right. Doing so can damage the latch 5. Grasp the latch and pull the drive out of the drive slot. Related Information ■ “Install a Hard Drive” on page 73 ■ “Four-Drive Capable Backplane Configuration Reference” on page 77 ■ “Eight-Drive Capable Backplane Configuration Reference” on page 78 ■ “Sixteen-Drive Capable Backplane Configuration Reference” on page 79 ▼ Install a Hard Drive Installing a hard

Downloads : 4   Arquivo Tamanho: 11 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

¦ “Safety Information” on page 63 ¦ “Required Tools” on page 66 ¦ “Obtain the Chassis Serial Number” on page 66 ¦ “Obtain the Chassis Serial Number Remotely” on page 66 ¦ “Powering Off the System” on page 67 ¦ “Extending the Server to the Maintenance Position” on page 69 ¦ “Remove the Server From the Rack” on page 71 ¦ “Perform Electrostatic Discharge – Antistatic Prevention Measures” on page 73 ¦ “Remove the Top Cover” on page 73 Related Information ¦ “Managing Faults” on page 11 ¦ “Servicing C

Downloads : 10   Arquivo Tamanho: 10 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

See “Run POST in Maximum Mode” on page 28. POST error messages use the following syntax: c :s > ERROR: TEST = failing-test c:s > H/W under test = FRU c:s> Repair Instructions: Replace items in order listed by H/W under test above c: s > MSG = test-error-message c:s > END_ERROR In this syntax, c = the core number, s = the strand number. Warning and informational messages use the following syntax: 42 SPARC Enterprise T5440 Server Service Manual • July 2009 INFO or WARNING: message In COD

Downloads : 0   Arquivo Tamanho: 8 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

. Do not touch the circuitry on boards and soldered parts. Hold the metallic areas or the edge of the circuit boards. . Follow the safety instructions in the "Safety instructions" on page 31. 8.7.1 Required tools . Starting and completing the task: – key for the rack doors (if applicable) – Phillips Ph2 screw driver . Installing the expansion card: tool-less 148 Maintenance Manual RX900 S1 Expansion cards and BBU 8.7.2 Starting the task E Perform the following procedures: 1. "Opening the rack do

Downloads : 6   Arquivo Tamanho: 5 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

Is not lit when the management blade is not active (slave) 2 LAN activity indicator (service LAN connection) Lights up green if a LAN connection exists. Does not light up if no LAN connection exists. Flashes orange when a LAN transfer is in progress. 3 LAN transfer-rate indicator (service LAN port) Lights up green for a LAN transfer rate of 100 Mbit/s. Does not light up for a LAN transfer rate of 10 Mbit/s. BX900 S1 Operating Manual Installation and operation 4 Global Error indicator (orange) –

Downloads : 36   Arquivo Tamanho: 4 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

BX600 S3 Operating Manual Updating BX600 System Components Preparation for Use and Operation E Extract the firmware file to the root directory of the TFTP file system. For information on the image file names, see the readme file of the update package. E Start an Internet browser on the client server. Enter the IP address specified above in the address field. Enter the user name and password admin. The home page is displayed. E In the navigation bar choose Flash/File. I Only two operation code im

Downloads : 6   Arquivo Tamanho: 4 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

User must not perform these tasks. Incorrect operation of these tasks may cause electric shock, injury, or fire. ■ Installation and reinstallation of all components, and initial settings ■ Removal of front, rear, or side covers ■ Mounting/de-mounting of optional internal devices ■ Plugging or unplugging of external interface cards ■ Maintenance and inspections (repairing, and regular diagnosis and maintenance) Caution — The following tasks regarding this product and the optional products p

Downloads : 5   Arquivo Tamanho: 4 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

If the system is at the ok prompt, type boot. 3. Use the set /SYS keyswitch_state=normal command to return the virtual keyswitch to Normal mode (default) so that the system can power on and start the boot process. | -> set /SYS keyswitch_state=normal 54 SPARC Enterprise T5120 and T5220 Servers Installation Guide • August 2007 ▼ To Connect to the System Console Output from POST, OpenBoot, and the Solaris OS is displayed in the system console using the network console on the service processor

Downloads : 0   Arquivo Tamanho: 4 mb   Fabricante : Fujitsu  
Categoria : Computadores
@name

When you install a server blade in the basic unit, an important factor is the height. Figure 28 shows a 2-way server blade, which occupies one slot in the basic unit. Figure 28: PRIMERGY BX620 S3/S4 2-way server blade PRIMERGY BX600 S2 Basic Unit Server Blades The 4-way server blade is twice the height and occupies two slots (figure 29). Figure 29: PRIMERGY BX630 scalable server blade (4-way configuration PRIMERGY BX600 S2 Basic Unit Server Blades Installation Sequence 7.1 Installation Sequence





categorias