1 FEATURES AND FUNCTIONS .............................. 2 NAME OF PARTS ................................................... 3 PREPARATION ....................................................... 5 OPERATION ........................................................... 6 TIMER OPERATION ............................................... 8 SLEEP TIMER OPERATION ................................... 9 MANUAL AUTO OPERATION ............................... 9 ADJUSTING THE DIRECTION OF AIR CIRCULATION .......

In the event of compressor failure during heat pump operation, unit shall automatically switch to electric resistance heat to maintain selected room temperature regardless of outdoor temperatures. Specifications for Optional Internal Condensate Removal (ICR) system for 3900 or 5800 series heat pump units. The unit shall have a factory-installed Internal Condensate Removal (ICR) system to permit unit to automatically dispose of heat pump generated condensate water with no overflow to outdoors dur

Ref. No. Description Part No. Ord. Q'ty Ref. No. Description Part No. Ord. Q'ty RY-36FA RY-36UA RY-36FA RY-36UA 8 Air Filter 9359739005 9359739005 338-2 Motor Fixture-B 9359703006 9359703006 12 Base Assy 9359680000 9359680000 345-1 Filter Guide-R 9359692003 9359692003 34 Capacitor (Fan Motor) 9900270216 9900270216 345-2 Filter Guide-L 9359693000 9359693000 56 Sirocco Fan Assy 9359701002 9359701002 361 Bushing 9359733003 9359733003 63 Panel (Front) 9359734000 9359734000 379 Hinge Plate (Grille) 9

6. Install the air filter. Please consult instructions for cleaning the air filter on page 12. 7. Close the intake grille. Push the intake grill in at 4 points (the two ends of its lower side as well as two center points of the lower side, as shown in the figure) to close it. If, after cleaning the dust collection unit, the operation indicator lamp and the timer indicator lamp flash during Air Cleaning, please ensure that the unit is not damp and that the intake grille is properly closed. If,

1 Carry out steps 1 to 2 of the “Setting Up the Weekly Timer Operation” procedure to select the day that you want to set as the DAY OFF. 2 Press the DAY OFF button. The DAY OFF setting is registered, and the DAY OFF caption appears on the display. . To cancel the DAY OFF setting: You can cancel the setting by pressing the DAY OFF button again. TIMER MODE SET ZONE START/STOP CLOCK ADJUST SET TIME TEMP./DAY FAN CONTROL MASTER CONTROL DAY OFF ENERGY SAVE PM PM TIMER DAY WEEKLY ON OFF DAY OFF 1COOL

(2) A flashing time value indicates that the system is in time-setting mode. To return to the clock display you must hold down the SET button for 3 seconds. (3) You do not need to set values for both WEEKLY 1 and WEEKLY 2. If you wish, you can set values only for WEEKLY 1 or only for WEEKLY 2. (4) The allowable range for the day’s time settings is shown below. (5) If you set the OFF time to occur on the day following the ON time, the NEXT DAY caption appears on the display. Cannot set 5 min. Ava

^ : Use to advance the day forward. Ў : Use to turn the day back. TIMER MODE SET ZONE START/STOP CLOCK ADJUST SET TIME TEMP./DAY FAN CONTROL MASTER CONTROL TIMER DAYWEEKLY ON OFF1COOL 1 2 3 ”. DAY CODE 1 2 3 4 5 6 7 DAY OF THE WEEK MON TUE WED THU FRI SAT SUN 3 3 Hold the SET button down for 3 seconds. The “WEEKLY 1” ON time starts flashing, and the fan speed and operating mode displays go off. 4 4 Press the SET TIME button to set the day’s first ON time. ^ : Use to advance the time forward. Ў :

. . . . . . .2, 3 Operating Instructions . . . . . .4, 5 Additional Controls . . . . . . . . . . .5 Controls . . . . . . . . . . . . . . . . . . . .4 Normal Operating Sounds . . . . .5 Care and Cleaning Air Filter . . . . . . . . . . . . . . . . . . .6 Grille and Case . . . . . . . . . . . . . .6 Grille Frame Removal . . . . . . . . .6 Outdoor Coils . . . . . . . . . . . . . . .6 Installation Instructions Through-the-Wall Installation—Optional . . . . . . . .13 Window Installation . . . . . . .

The configuration of the electrical plug conforms to NEC standards for the circuit amperage and the position of the wires in the nine-pin connector determines the heater wattage and current requirements when it is plugged into the Zoneline chassis. The power connection kit is selected by the amperage of the circuit where it will be installed. Each line cord kit has an integral Leakage Current Detection and Interruption (LCDI) or Arc Fault Current Interrupter (AFCI) device as required by the Nati

ELECTRIC EXPANSION VALVE CN12 B6B-XASK-1-A WHITE CN12-4 UL1430 AWG24 ORANGE CN12-1 UL1430 AWG24 RED CN12-2 UL1430 AWG24 BROWN CN12-3 UL1430 AWG24 BLUE CN12-5 UL1430 AWG24 YELLOW CN12-6 UL1430 AWG24 WHITE CN14-1 UL1015 AWG20 BLUE CN14-2 UL1015 AWG20 BLUE HIGH PRESSURE SWITCH PRES. SW CN11 B6B-XAKK-1-A BLACK THERMISTOR CN1 B3P5-VH-B-C BLACK CN2 B2P3-VH-B-Y YELLOW CN3 B4P7-VH-B-R RED CN4 B2P3-VH-B-Y YELLOW CN5 B4P7-VH-B WHITE CN6 179844-1 WHITE CN7 179844-4 YELLOW CN8 B2P3-VH-B-R RED K7 FTR-F3A K6