Back off the screw until its head rests on the stopper on the opposite handle. Back off the screw 1/6th of a turn at a time and hold tool to the light, observing result of gap setting. 3. To verify the gap, place a sheet of paper between the jaws and fully close the handles. The jaws should hold the paper in place. Hold the screw in place and tighten the lock nut. DO NOT OVER TIGHTEN the nut. AWARNING To prevent serious injury: 1.Wear ANSI-approved safety goggles during use. 2.Never use on l

Chargers should not be left plugged in or charging for more than 2 hours. Operation Install saw blade. Prepare and secure the material to be cut before turning on saw. Battery should have a full charge before using saw. Refer to illustrations that follow. Remove battery before making any adjustments. Warning: Do not hold tool by the handle while making adjustments as your fingers may touch the Switch and Safe buttons and start the saw. Installing Cutting Blade 1. Remove battery. 2. Press on the

For a shallower cut, slide the Adjustable Shoe Plate further away from the Guard Plate. (See Figure C.) 3. Then, retighten the two Hex Screws (58). (See Figure C.) BOTTOM VIEW HEX SCREW GUARD PLATE (2) ADJUSTABLE SHOE PLATE FIGURE C (58) (1) Operating Instructions: 1. The Reciprocating Saw is equipped with a Trigger Lock mechanism. To operate the tool for extended periods of time squeeze and hold the Trigger (37), then press the Trigger Lock. To unlock the Trigger Lock mechanism, squeeze and rel

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions please call Harbor Freight Tools at telephone number 1-800-444-3353. Specifications: Length: 4-3/4” Height: 2-1/2” Width: 4” Extended Maximum Capacity: 2” Stock Bushing Set: 2 each of 1/4”, 5/16” and 3/8” Note: There are 4 holes along the top of the Jig. Only 2 of the holes accept threaded bus

Always position the Saw safely and activate the Throttle Lever (13) repeatedly to make sure all of the air is expended. Refer to FIGURES 2 and 3 below, and the Assembly Drawing on page 8. 1. The Blade Guard (34) may be removed when replacing blades, but it must always be on during operation. Using the Saw without the Blade Guard (34) can result in severe injury. To remove the Blade Guard (34), loosen and remove the two Set Screws (24). When replacing the Blade Guard (34), place it in the slots a

13. Make sure the Cutting Wheel Blade (8) is wet at all times when cutting. 14. When operating the Tile Saw, always make sure to fill the Tray (17) with enough clean, cold water to cover the lower edge of the Cutting Wheel Blade (8), but not so deep as to spill over the edge of the Tray. Make sure the water supply for the Tile Saw is not dirty, sandy, and does not contain any corrosive chemical products. Change the water when necessary while in use and rinse out the Tray (17) after every use. 15

Assembly Install Blade Refer to the photo on the top of the next page. 1. Select the saw blade best suited for stock you are cutting. Wood blades have a coarser tooth pitch. Metal blades have a finer tooth pitch. Use each blade only for cutting its specified stock. 2. Using the supplied Hex Key Wrench, loosen, but do not remove Screw (4). 3. Slide the blade (teeth down) into the blade holder as far as possible. 4. Tighten Screw (4). SKU 42597 Page 4 Screw (4) Blade Screw (4) Blade Adjusting Shoe

Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. WEAR PROPER APPAREL. Do not 10. wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. ALWAYS USE SAFETY GLASSES. 11. Also use face or dust mask if cutting operation is dust

It may be used on wood or metal stock. Read this manual before attempting to use the Jigsaw. OPERATION General Avoid overloading the tool. Do not apply excessive pressure to the saw while cutting. If the speed drops abnormally, decrease pressure immediately. If the blade stops abruptly or becomes blocked, turn saw off at once. Never use damaged blades. Ensure the safety of the work space. Clear the work area of all parts and debris that may cause injury by becoming flying objects. Use a stab

Operation Warning! Unplug the power cord while setting up the saw and workpiece. Do not plug in until ready to cut. Note: Steel Capacity Cutting Chart found on page 5 of this manual. Warning: This Cut-Off Saw is designed to cut iron metal. Do not cut wood, brick, aluminum, or magnesium; tool damage and/or personal injury could occur. Before using the saw always check the following: A. Make sure the blade (not included) is securely attached. Loosen Screw (#110) and lift Small Cover (#109) out of