Log:
Downloads : 2   Arquivo Tamanho: 2 mb   Fabricante : Delta  
Categoria : Jig Saw e
@name

NOTE: Loosely tighten the screws for further adjustment. B A C D Fig. 9 11 3. Locate the 1/4-20x2." hex head screw (G) Fig. 10. Place the 1/4" internal tooth lockwasher (O) M6.4 flat washer (P) and the 1/4" external tooth lockwasher (R) on the screw (G). 4. Position the recessed end (E) Fig. 11 of the splitter bracket (B) against the end of the pivot rod (F), and fasten using the assembly in STEP 3. NOTE: Loosely tighten the hardware for further adjustment. 5. Position the splitter (H) Fig. 13 a

Downloads : 19   Arquivo Tamanho: 2 mb   Fabricante : Delta  
Categoria : Jig Saw e
@name

Let the motor cool three to five minutes. Push the reset button (C) to reset the overload device. The motor can then be started again in the usual manner. BLADE HEIGHT ADJUSTMENT To adjust the height of the saw blade, turn the handwheel (A) Fig. 29. Turning the handwheel clockwise lowers the blade and turning the handwheel counterclockwise raises the blade. A Fig. 29 15 To tilt the saw blade, loosen the lock handle (A) Fig. 30 and move the handwheel (B) until the blade is at the desired angle. T

Downloads : 0   Arquivo Tamanho: 663 kb   Fabricante : Delta  
Categoria : Jig Saw e
@name@name@name@name

17 and 18, can be opened as follows: MOVING PARTS. LAZERATION / PINCH HAZARD: NEVER OPEN THE DOOR WHEN THE MACHINE IS RUNNING. 1. Press in the two locking latches (A) Fig. 17, and swing door (B) open. 2. Fig. 18, illustrates door (B) in open position. 3. To close and fasten door (B) Figs. 17 and 18, press on door directly over latches (A) Fig. 17, until latches snap into the locking position. 11 B A Fig. 17 B Fig. 18 ADJUSTING BLADE TENSION Blades of 1/8", 1/4", and 3/8" in width by 59-1/2" in l

Downloads : 0   Arquivo Tamanho: 663 kb   Fabricante : Delta  
Categoria : Jig Saw e
@name@name@name@name

3. Have cord replaced. Remedy 1. Replace with adequate size cord. 2. Feed stock more slowly. 3. Clean or replace blade. 4. Contact your electric company. Remedy 1. Tighten all mounting hardware. 2. Reposition on flat level surface. 3. Replace belt. 4. Adjust belt tension by moving motor. 5. Tighten all mounting hardware. Remedy 1. Replace with adequate size cord. 2. Contact your electric company. Remedy 1. Adjust blade tension. 2. Check and adjust blade guides. 3. Adjust blade support bearing. 4

Downloads : 1   Arquivo Tamanho: 26 kb   Fabricante : Delta  
Categoria : Jig Saw e
@name

A machine incorrectly assembled can cause serious injury. 2. OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety. 3. FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution. 4. SECURE THE MACHINE TO A SUPPORTING SURFACE. Vibration can cause the machine to slide, walk, or tip over. 14. DO NOT CUT A WORKPIECE THAT DOES NOT HAVE A FLAT SURFA

Downloads : 0   Arquivo Tamanho: 10 mb   Fabricante : Delta  
Categoria : Jig Saw e
@name

and Model No. plate is attached to the top surface of the frame casting. This plate can be seen by removing the front guard and looking behind the left edge of the upper blade wheel. Locate this plate and record the Serial No. and Model No. in your manual for futur^ reference. SERIAL NO. _ MODEL NO__ PART NO. 1088294 DATED 5-25-77 SAFETY RULES FOR ALL TOOLS As with all power tools there is a certain amount of hazard involved with the operator and his use of the tool. Using the tool with th

Downloads : 3   Arquivo Tamanho: 4 mb   Fabricante : Delta  
Categoria : Jig Saw e
@name

Move the miter gage towards the rear and check if the saw teeth touch the cut end of the strip the same amount. 9. If the teeth at the rear do not touch, then it is apparent that the material is moving in a line away from the blade. This means that the mechanism below the table must be adjusted so that the miter gage slots in the table will be parallel to the blade. 10. Remove motor plug from electrical outlet, and tilt saw blade to 45°. 11. Use a V299 socket wrench long enough to reach the t

Downloads : 1   Arquivo Tamanho: 4 mb   Fabricante : Delta  
Categoria : Jig Saw e
@name@name@name

3. If the size or shape of the workpiece would cause your hands to be within 6" (152.4 mm) of the saw blade, use a push stick to complete the cut (Fig. 53) The push stick can easily be made from scrap material as explained in the section Constructing A Push Stick. 4. Ripping narrow pieces can be dangerous. If possible, rip the narrow piece from the larger piece. If the workpiece is short enough, use a pushboard. (A pushboard can be constructed as shown in Fig. 54 and used as shown in Fig. 55.) N

Downloads : 6   Arquivo Tamanho: 30 kb   Fabricante : Delta  
Categoria : Jig Saw e
@name

1. DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury. 2. OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety. 3. FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution. 4. DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTA

Downloads : 62   Arquivo Tamanho: 26 kb   Fabricante : Delta  
Categoria : Jig Saw e
@name

Check to see that they are in place, properly adjusted, secured, and working correctly. 5. USE PROPER BLADE SIZE and type. 6. ADJUST THE UPPER BLADE GUIDE so that it is about 1/8" above the workpiece. 7. PROPERLY ADJUST the blade tension, tracking, blade guides, and blade support bearings. 8. KEEP ARMS, HANDS, AND FINGERS away from the blade. 9. AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause a hand to move into the blade. 10. NEVER START THE MACHINE before clea





categorias