Maintenance WARNING. Always ensure that the tool is switched off and the plug is removed from the power point before making and adjustments or maintenance procedures. When you have finished cutting your tiles, always disconnect the power, empty the water and fully clean and dry the machine. Installing a blade DANGER. • Never try to use a blade larger than the stated capacity of the saw. It will come into contact with the blade guard. • Never use a blade that is too thick to allow the outer blade

11400W TILE AND TRIM CIRCULAR SAW TTS5000M INSTRUCTION MANUAL BlackCyanMagentaYellowCode:TTS5000MDate: 070206Edition: 13Op: DCRBlackCyanMagentaYellowCode:TTS5000MDate: 070206Edition: 13Op: DCR ContentsContents Warranty 2 Introduction 3 Environmental protection 3 Description of symbols 3 Specifications 3 General safety rules 4 Additional safety rules for laser lights 5 Additional safety rules when using water cooling system 6 Additional safety rules for tile and timber cutting saws 6 Testing your

5. Do not charge batteries for “top up”. Batteries should be placed on charge only when the battery is noticeably running down or the tool no longer performs a task it previously performed. 6. Unplug the adaptor charger and charging slide when not in use and store them in a dry, secure place. 7. Do not charge your battery pack in temperatures below 0°C or above 40°C. 8. Always remove the battery pack and store it in a dry, secure place when the tool is not in use. 9. Battery charging should only

CAUTION. Make sure that the mounting surface is not warped as an uneven surface can cause binding and inaccurate sawing. Release knob The release knob (6) is provided for holding the cutting head down whilst transporting or storing the mitre saw (fig. E). The saw must never be used with the release knob locking the head down. Slide lock When tightened, the slide lock (22) prevents the saw head from sliding. Tighten the slide lock during transportation (fig. F). Mitre table locks The mitre table

Push the on/off switch (2) forward and up over the latching ramp to lock the switch on (fig C). To turn off the tool, press the back of the switch and lift it over the latching ramp (fig D). CAUTION. Allow the blade to come to a complete standstill before setting the jigsaw down. Blade guard The blade guard (6) should always be in position when operating the jigsaw. It can be removed to allow easier access when changing blades (fig E). Blade guide The grooved disc blade guide (7) is spring loade

A Copyright © 2005 Delta Machinery INSTRUCTION To learn more about DELTA MACHINERY visit our website at: For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY GUIDELINES - DEFINITIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

• Always adjust the drop foot to just clear the workpiece to protect the operator, keep blade breakage to a minimum and provide maximum support for the blade. • Always adjust blade tension correctly. • The scroll saw should cut on the down stroke. Always make sure blade teeth are oriented downward towards the table. • When cutting a large piece of material make sure it is supported at table height. • Hold the work firmly against the table. • Do not feed the material too fast while cutting. Only

INSTRUCTION MANUAL 2000W 250mm (10”) Table Saw with Laser Line Generator* * Patent Pending LS250TS 061004 ED8 DCR • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris 2 Contents ...................................................................................................................................................................................................................................................................................

The mitre table features positive click stops at 0°, 15°, 22.5°, 30° and 45° for quick setting of common mitre angles. WARNING. Be sure to tighten the mitre table lock before making a cut. Failure to do so could result in the table moving during the cut and cause serious personal injury. Bevel lock The bevel lock (16) is used to set the blade at the desired bevel angle (fig. G). The mitre saw bevel cuts from 0° to 45° to the left and right. To adjust the bevel angle loosen the bevel lock and pul