There are a lot of people who still believe you can only get straight, splinter.free cuts in a shop using expensive panel saws, table saws, and CNC equipment. Getting quality cuts with portable power tools doesn’t have to be difficult or expensive. The truth is…that with the right tools, anyone can get great results in the shop or on the jobsite. Straight, splinter.free cuts are easy, once you know the secret. Let’s start with the basic causes of poor quality cuts. Unwieldy panels, arbor run.out

To prevent injury or electrocution, always unplug the tool from the power supply outlet before performing any maintenance or repair work on the tool! Do not use compressed air to clean the motor housing of the tool, as you could inject foreign objects into the motor through the ventilation openings. Compressed air may be used on other components, but personal safety protection should be employed (hearing, vision, and respiratory). Certain cleaning agents and solvents are harmful to plastic parts

Manual de instrucciones Pagina 22 - 31 IMPORTANTE: Lea y comprende todas las instrucciones antes de usar. Instruction manual Guide d’utilisation Manual de instrucciones MFT/3 MFT/KAPEX 475235_003 2 Table of Contents Health hazard by dust Technical data 3 Symbols 4 Design 4 Intended use 4 MFT/3: Setting up and assembly 5 Step 1: Setting up 5 Step 2: Trim splinter guard 5 Step 3: Setting up the guide rail support 6 Step 4: Attaching the guide rail 7 Step 5: Attaching the pre-set profi le setting r

Secure the guide rail in this position with the two screws [5-1] and tighten using the hexagon wrench. Lower the guide rail onto the support unit so that the groove in the underside of the guide rail fi ts on to the pin [4-5] of the support unit. The guide rail is properly attached when only a very slight lateral pressure is necessary for the pin to engage into the guide rail. The defl ector [6-1] is pushed onto the end of the guide rail. Close the rotary knob [6-2]. The defl ector prevents the

484 455 (pack of 1) 2 are needed to connect 2 tables together PRODUCT DESCRIPTION The MFT table connector can be used to connect 2 or more Multi-Function Tables to get a larger work surface. These strong metal bars with 4 set screws slide into the "T" track spanning the tables to be joined as shown below. SUGGESTED USAGE For big jobs where a large surface with very versatile clamping options is needed. MFT's can also be joined together and be used with a long guide rail (e.g. FS 1900/2) to

Using too small of an extension cord can cause the cord to overheat. Extension Cord Ratings Cord Length Size (AWG) <25 Ft. 14 25-50 Ft. 12 50-100 Ft. 10 >100 Ft. Not recommended Personal Safety > Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. > Use personal protective equipm

Manual de instrucciones Pagina 10- 13 IMPORTANTE: Lea y comprende todas las instrucciones antes de usar. KA-KS 120 475825_001 Trimming attachment KA-KS 120 right 2 x KA-KS 120 Scope of delivery The trimming attachment consists of the following main components: (1.1) Stop profile left (1.2) Tape measure clamp (1.3) Support (1.4) Support plate (1.5) Stop flag (1.6) Adjustable spacer (1.7) Extendable end piece (1.8) Leg support plate (1.9) Tape measure (1.13) Cross brace 1.9 1.8 1.7 1.6 1.5 1.4 1.3

Contents General Safety Rules...........................................................................................................................................................................3 Specific Safety Rules for Circular Saws........................................................................................................................................4 Tool Description.........................................................................................................

Thechip trajectory can be altered by turning the chip guard asrequired. This prevents the operator being subjected to astream of chips, always providing that the chip guard isadjusted so that the chip trajectory is directed away from theoperator. 3.4Changing the saw blade Check regularly whether the saw blade is in goodcondition. Saw blades which are cracked or have changedshape should no longer be used, but changed immediately! When selecting the saw blades it is essential that the followingpoi