315.220381 Save this manual for future reference. • Safety CAUTION: Read and follow all • Features Safety Rules and Operating • Assembly Instructions before first use of this product. • Operation • Maintenance Customer Help Line: 1-800-932-3188 • Parts List Sears, Roebuck and Co., Hoffman Estates,lL 60179 USA Visit the Craftsman web page: ® 972000-705 10-99 FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL ARM SAW If this CRliFT,_MAN" Radial Arm Saw fails due to a defect in material or workmanshipwithi

Failure to heed this warning can result in serious personal injury. CUTTING WITH YOUR COMPOUND MITER SAW ,& WARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury. CROSSCUTTING

14 Squeeze the switch trigger to start your saw. Always let the blade reach full speed, then guide your saw into the workpiece. _IL WARNING: The blade coming in contact with the workpiece before it reaches full speed could cause your saw to "kickback" towards you resulting in serious injury. When making a cut use steady, even pressure. Forcing causes rough cuts, could shorten the life of your saw and could cause "kickback." REMEMBER: When sawing through work, the lower blade guard does not cover

Following this rule will reduce the risk of sedous personal injury. 9. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If someone borrows this tool, make sure they have these instructions also. 6 ADDITIONAL SPECIFIC SAFETY RULES cont. /_, WARNING: Some dust particles created by power sanding, sawing, grinding, drilling and other construction jobs contain chemicals known to cause cancer, birth defects or other reproductive harm. Some exampl

Using a dull blade will place a heavy load on your saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available. Gum and wood pitch hardened on blades will slow your saw down. Use gum and pitch remover, hot water, or kerosene to remove these accumulations. Do not use gasoline. BLADE GUARD SYSTEM The lower blade guard attached to your circular saw is there for your protection and safety. It should never be altered for any reason. If it becomes dama

315.214770 _1_ WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer HeUp Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 BeverUy Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: 983000-577 Save this manual for future reference 8-04 [] Warranty ................................................................................................................................................................

Otherwise, it could get wedged against the blade and thrown violently. . Only the workpiece should be on the saws table. . Secure work. Use clamps or a vise to help hold the work when it is practical. USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES. . Use extra supports (tables, sawhorses, blocks, etc.) for workpieces large enough to tip. . Never use another person as a substitute for a table extension, or as an additional support for a workpiece that is longer or wider than the basic mite

Also, when a new blade is installed, it is necessary to check the clearance of the blade to the miter table support before starting the saw. Make adjustments if needed. DEPTH STOP ADJUSTMENTS See Figure 25. • Unplug your saw. A WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. To adjust the depth stop use a 17 mm wrench or adjustable wrench and loosen the hex nut at the rear of the miter saw arm. Use the 5 mm hex key provided to adj

WARNING ON OFF a CRRFTSMRN ° ConsumerHelp Line 1-800-932-3188 WARNING / ADVERTENCIA Fig. 3 Thisversatilevariablespeedscrollsawisgreatfor makingtoys,puzzles,games,artwork,andjewelry.It isahandydo-it-yourself tool.Itcutswood,wood compositionplastic,andotherfibrous products, materialupto2 inchesthick.Italsocutsnonferrous metals(aluminum,brass,copper). KNOW YOUR SCROLL SAW Before attempting to use your saw, familiarize yourself with all operating features and safety requirements of your Sears Crafts

1t3.2473t0 BAND SAW WITH CABINET S_rial Number __ Model and serial numbers may be found at the left-hand side of the base. You should record both model and serial number in a safe place for future USe. im N CAUTION: READALL INSTRUCTIONS CAREFULLY 113.247310 113.24 7210 CRRFTSMRN 12-1NCH BAND SAW • assembly • operating • repair parts _,. j ..... _,' Sold by SEARS,ROEBUCKAND CO., Chicago, IL 60684 U.S.A. Part No. SP5086 Printed in U.S.A FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAW If within one ye