Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
and spray-type lubricating oil. CAUTION: • Do not wash the blades in water. Failure to do so may cause rust or damage on the tool. 7 Removing or installing shear blade Removing or installing shear blade CAUTION: • Before removing or installing shear blade, always be sure that the tool is switched off and unplugged. • When replacing the shear blade, always wear gloves without removing blade cover so that hands and face does not directly contact the blade. Failure to do so may cause personal injury. NOTE: • Do not wipe off grease from the gear and crank. Failure to do so may cause damage to the tool. • For specific way of removing and installing shear blades refer to the reverse of a package for accessory shear blades. Removing the shear blades Reverse the tool and loosen four screws. 1 1. Screws 2. Blade cover NOTE: • Be careful not to get your hands dirty as grease is applied in the shear blade driving area. Remove the under cover. 12 Remove the gear housing cover. 1. Under cover 2. Blade cover 1. Gear housing cover Set the crank at the angle as shown in the figure with a slotted bit screwdriver. 1. Crank 1 009298 Remove two screws from the shear blades and the shear blade unit will be taken out. 12 1. Screws 2. Shear blade 009299 CAUTION: • Return the gear to the original position in such a manner as it was installed if it should be taken away by mistake. Installing the shear blade Prepare 4 removed screws (For under cover), 2 screws (For shear blade), gear housing cover, under cover, and new shear blades. Adjust the crank position as shown in the figure. At this time, apply some grease provided with new shear blades to the periphery of the crank. 1. Crank 1 009300 Overlap the oval hole in the upper blade with that in the lower one. 1 8 1 1 Ellipse of shear blade Take out the blade cover from the old shear blades and fit it onto the new ones for easy handling during the replacement of blades. Place the new shear blades on the tool so that the oval holes in the shear blades fit onto the crank. Overlap the holes in the shear blades with the screw holes in the tool and then secure them with two screws. 12 1. Ellipse of shear blade 2. Crank Check the crank for smooth turn with a slotted bit screwdriver. 1. Crank 1 Install the gear housing, under cover on the tool. Tighten the screw firmly. Remove the blade cover and then turn on the tool to check it for proper movement. NOTE: • When the shear blades does not operate properly, there is a poor fit between the blades and crank. Redo from the beginning. Storage The hook hole in the bottom of the blade cover is convenient for hanging the tool from a nail or screw on the wall. 009305 Put the blade cover on the shear blades so that the blades are not exposed. Store the tool out of the reach of children carefully. Store the tool in the place not exposed to water and rain. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Dolmar Authorized Service Centers, always using Dolmar replacement parts. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Dolmar tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Dolmar service center. • Extension cord • Blade cover • Hook complete • Shear blade assembly • Waist cord hook • Arm cord hook 9 FRANCAIS FRANCAIS Modele HT-345 HT-355 HT-365 Longueur de la lame 450 mm (17-3/4") 550 mm (21-5/8") 650 mm (25-5/8") Nombre d'impacts par minutes 1 600/min. 1 600/min. 1 600/min. Longueur totale 862 mm (34") 970 mm (38-1/4") 1 042 mm (41") Poids net 3,6 kg (7,9 lbs) 3,7 kg (8,2 lbs) 3,8 kg (8,4 lbs) • Etant donne l'evolution constante de notre programme de recherche et de developpement, les specifications contenues dans ce manuel sont sujettes a modification sans preavis. • Les specifications peuvent varier suivant les pays. • Poids conforme a la procedure EPTA du 01/2003 USB093-3 CONSIGNES DE SECURITE IMPORTANTES AVERTISSEMENT: LORSQUE VOUS UTILISEZ CET OUTIL, LES PRECAUTIONS DE SECURITE DE BASE DEVRAIENT TOUJOURS ETRE SUIVIES AFIN DE REDUIRE LES RISQUES D'INCENDIE, DE CHOC ELECTRIQUE ET DE BLESSURE PERSONNELLE, Y COMPRIS : LISEZ TOUTES LES INSTRUCTIONS. • Pieces de rechange - Utilisez seulement des pieces de rechange identiques pour l'entretien. • Fiches polarisees - Afin de reduire les risques de choc electrique, cet outil est dote d'une fiche polarisee (une lame est plus large que l'autre), ce qui exigera l'utilisation d'un cordon prolongateur polarise. La fiche de l'outil pourra etre inseree dans un cordon prolongateur polarise dans un seul sens. Si la fiche n'entre pas parfaitement dans la prise du cordon prolongateur, inversez sa position. Si elle n'entre toujours pas, procurez-vous un c...
Este manual também é adequado para os modelos :Clippers - HEDGE HT-355 (1.96 mb)
Clippers - HEDGE HT-345 (1.96 mb)