If the strips become bent back, they can be unbolted and turned around to improve clean out. Upper Auger Knives can be turned over for use of a new cutting edge and should be periodically sharpened, or replaced if they are no longer sufficiently breaking up material. Lower auger knives can be rotated several times before sharpening or replacement is required. Motor fan guard must be kept clean to allow sufficient air flow for proper motor cooling. Drive belts must be checked for wear and hardnes

These have been written for your safety and convenience, and to keep your unit running trouble-free for many years. MODEL AND SERIAL NUMBER INFORMATION is located on the drive input end panel. This is the number to give service personnel for parts and service questions. ADDITIONAL MANUALS and safety decals may be obtained through your dealer, or by writing to the address below. Order operators manual # 005810 all models Order service parts manual # 005815 for 3015 Order service parts manual # 00

Load cells and weigh bars should be kept clean, dry & lubricated to insure dependability. Normal scale activity: Some warm up scale drift may occur after the scale is turned on but should zero balance within 10-15 minutes. Scale may zero shift over night due to temperature changes. Weight may change slightly due to terrain changes when mixer is moved. Vertical check bolts must not be tight (and should be free to rotate by hand) and need not less than 1/16” and no more than 3/32” free play when p

1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIONS MODEL: 3015 * * * shields removed for illustrative purposes 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIONS MODEL: 3020 * * * shields removed for illustrative purposes KUHN KNIGHT INC. 1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIO

Kuhn Knight Inc. will not be responsible for damage caused by overloading, wet hay or foreign objects. WARNING Do not use tough hay (20%-60% moisture) Always use cured, dry hay. Wet hay, foreign objects or overloading may cause binding and damage to the mixer. Do not overload HAY MAXX SYSTEM with too much hay. This can cause bridging over the auger. If this occurs never attempt to release jammed materials or clean out materials from the Hay Maxx area without stopping mixer and locking out power

If your particular installation is such that a person may inadvertently put an arm or leg in these areas during operation, then additional safety shielding must be installed to prevent such an occurrence. Additional shielding of the motor and drive belt area may also be necessary depending on exact installation. AUGER KNIVES The upper and lower auger knives are installed to help handle long materials such as long stem hay. If you do not intend to handle this type of material, the knives can be r

If reel is over full, mixing action will be greatly reduced. Feed must not pile up between the reel and the side of the mixer. This causes a buildup of pressure, increases the power requirements of the mixer, and can cause pipes to bend. Load hay on the auger side of the mixer. This keeps hay from being caught between the reel pipes and side of mixer during initial loading. Break up bales before loading. Move reel cross pipes to the inner setting by compressing the springs and adding bolts and l

See Mixer Operation for recommended loading sequence. If forage is piled above reel, they may be wedged against the side when started up. KUHN KNIGHT INC. 1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 TROUBLE SHOOTING PROBLEM: MOTOR RUNS, BUT REEL AND AUGERS DO NOT TURN CAUSE SOLUTION SHEAR BOLT ON PTO DRIVELINE HAS SHEARED BELTS ARE SLIPPING BROKEN CHAIN Replace with Same Grade and size shear bolt. Do not us any bolt other than a Gr 5 see P

DANGER: NEVER ATTEMPT TO RELEASE JAMMED MATERIALS OR CLEAN MATERIALS from any area of the mixer or discharge chute without stopping mixer and locking out the power first. Moving parts can be hidden by materials, and stopped parts can start unexpectedly, causing severe injury. Always stop mixer and lock out power before attempting to remove jammed material or clean. Be aware that the spring-loaded reel arms can spring back unexpectedly, causing injury. DANGER: DO NOT ALLOW OPERATION of this unit