KCUE This button cue-monitors the signal of the ST IN channel (L/R are linked). This is linked with the ST IN section [CUE] keys on the M7CL’s panel. If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is not checked, this will not be linked with the M7CL console. LON Switches the ST IN channel on/off (the L/R settings are linked). This is linked with the ST IN section CH [ON] keys on the M7CL’s panel. The button is color-coded and indicates status as follows: White: ST IN channel is on (normal mode) Gray: ST IN channel/Send are off. Other colors: Send is on (SENDS ON FADER mode). If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is not checked, this will not be linked with the M7CL console. MFader Adjusts the input level of the ST IN channel. When the M7CL itself is in other than SENDS ON FADER mode, this is linked with the INPUT section faders of the M7CL’s panel. The fader is color-coded and indicates status as follows: White: You can adjust the input level of the .... .... .............. (normal mode). Gray: .... .... .............. is off. Other colors: You can adjust the send level (SENDS ON FADER mode). The current fader value is shown in the numerical box located immediately below the fader. This is the same as the fader for INPUT CH ( . p.18). If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is not checked, this will not be linked with the M7CL console. N Channel number This is the number of the ST IN channel. You can double-click this number to open the Selected Channel window for this channel. If you hold down the (< >) key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. O Channel name This is a text box that displays the channel name. You can also edit the channel name in this text box. J K L 7 8 9 N M O NOTE NOTE NOTE NOTE MIX windo w In this window you can view and edit the parameters of MIX channels 1–16. The parameters shown in the window can be selected from the [View] menu or the menu that appears when you right-click ( key + click) in the window. You can access this window in the following ways. . From the [Windows] menu, choose [Overview] and then choose “MIX” . Use the navigation keys in the Master window to turn on the [MIX] button AOUTPUT PATCH Click here to select the output port that will be assigned to the MIX channel, from the following choices. 4 1 2 3 ES 1-ES24(M7CL-48ES) EtherSound output channels 1–24 OMNI1-OMNI8 OMNI OUT jacks 1–8 OMNI9-OMNI16(M7CL-32/48) OMNI OUT jacks 9–16 SLOT1-1, SLOT1-2...SLOT3-16 Input channels of an I/O card installed in slot 1–3 RACK1A, RACK1B...RACK8R(B) L/R outputs of Rack 1–8 2TROUT L, 2TROUT R L/R channels of the 2TR OUT DIGITAL jack If multiple patches have been made, only the first port is shown. If you change the patching in this window, the port that had been assigned until then will be cancelled, and only the newly selected port will be assigned. BEQ (Equalizer) Switches the EQ on/off. This is the same as the equalizer for INPUT CH (. p.17). CDYN1(Dynamics 1) Switches the dynamics processor on/off. This is the same as the dynamics 2 for INPUT CH (. p.17). DINS (Insert) Enables/disables the insert-in. M7CL V3 Editor Owner’s Manual 22 These bar graphs indicate the send levels of the signals sent from the MIX • Pre/on (green)) 5 channel to MATRIX 1–8 bus. You can also adjust the send levels by dragging a bar graph to left or right. While you drag the bar graph, the send • Pre/off (green) level is shown in the numerical display area for TO STEREO/MONO. You can set the minimum value (–. dB) by holding down the • Post/on (yellow) (< >) key of your computer keyboard and clicking the bar graph, or set the nominal value (0.00 dB) by holding down the • Post/off (yellow) (< >) key and key and clicking the bar graph. The bar graph display will change as follows according to the send position (pre/post) and on/off status of the signal sent from the MIX channel to the MATRIX buses. To switch a send on/off, click the channel number located at the left of the bar graph. 6 FPAN/BALANCE The PAN knob adjusts the panning of the signal that is sent from the mix channel to the STEREO bus L/R channels (or the L/C/R channels). You can set this to the center value 7 by holding down the (< >) key of your computer keyboard and clicking this 8 knob. If assigned as a stereo bus, this adjusts the balance of the odd-numbered channel and even-numbered channel. The stereo bus setting can be made in Mix Bus Setup of 9 the Mixer Setup dialogbox. J The [ST] button is an on/off switch for the signal that is sent from the mix channel to the STEREO bus. The [MONO] button is an on/off switch for the signal that is sent from the mix channel to the MONO bus. K If LCR MODE is selected in the Selected Channel window, the [LCR] button will appear instead of the [ST] button and [MONO] button, and the [...
)
