IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instruct

Reference Manual This page intentionally left blank 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Table Of Contents Introduction..........................................................5 Welcome!......................................................................................................5 About the MultiMix FireWire...........................................6 All-In-One Mixer and Multichannel Computer Audio Interface ..........................................................................

Surge Cymbals are compatible with a variety of drum modules and can also be used to trigger sounds on any MIDI instrument using a “ Trigger to MIDI” interface. 1. Insert two .” stereo cables ( included) into the two connections in the trigger housing on the underside of the cymbal. 2. Place the cymbal onto a cymbal stand. Do not use a cymbal sleeve with this cymbal since it already has a built- in sleeve. Be sure the Choke Strip on the underside of the cymbal is on the side closest to you. 3. Co

HOW TO USE THIS MANUAL This manual is divided into the following sections describing the various modes of the XT. Though we recommend you take time to read through the entire manual once carefully, those having general knowledge about multitrack recorders should use the table of contents and index to reference specific functions while using the XT. Chapter 1: Introduction. Deals with the necessary preparation before recording and playing, including connections to external devices. This chapter a

AC power cable 3. Sustain Pedal 4. Reference Manual If anything is missing, please contact your dealer or Alesis immediately. Alesis contact information: Alesis Studio Electronics, Inc. Los Angeles USA E-Mail: support@alesis.com Website: Alesis Andromeda A6TM Reference Manual Revision 1.0 by Dave Bertovic Revision 1.1 by Brian R. Shim © Copyright 2001, Alesis Studio Electronics, Inc. All rights reserved. Reproduction in whole or in part is prohibited. “A6”, “QCard” and “FreeLoader” are trademark

1 Quick Start Owner's Manual (English) Quick Setup for the Bassfire .. Make sure all items listed on the front of this guide are in the Bassfire's box. .. Read the Important Safety Instructions document included with the Bassfire. .. Study the Hookup Diagram below. .. Make sure all equipment is turned off and all gain knobs are set to zero. .. Connect your Bass and other equipment to the Bassfire in the manner illustrated below. .. Plug in all devices and turn them on. .. Experiment with the Bas

4 How to Use This Manual .................................................................... 6 Important Safety Instructions...................................................7 Important Safety Instructions (English) .............................................. 7 Instructions de Securite Importantes (French) .................................... 9 Lesen Sie bitte die folgende Sicherheitshinweise (German).............11 CE Declaration Of Conformity ..............................................

1 Quick Start Owner's Manual (English) Quick Setup for the Coolfire .. Make sure all items listed on the front of this guide are in the Coolfire's box. .. Read the Important Safety Instructions document included with the Coolfire. .. Study the Hookup Diagram below. .. Make sure all equipment is turned off and all gain knobs are set to zero. .. Connect your guitar and other equipment to the Coolfire in the manner illustrated below. .. Plug in all devices and turn them on. .. Experiment with the C

TRIG MENU .........................................................................................................................................24 TRIGGER INPUT PARAMETERS...........................................................................................................24 TRIGGERING PARAMETERS................................................................................................................25 VELOCITY CURVE..................................................................

First, attach an inexpensive contact transducer to the center of the drum stand and plug it into a DM5 input. . Next, go to Ext Trig page 1 and select the Velocity Curve setting of 0 (Unassigned) for this trigger. . Go to the next page and set the Xtalk, Decay and the Noise levels all to 00. This low level will allow the maximum amount of Noise and stand vibrations to be detected by the DM5. . Using the TRIG LEVEL meter (at the bottom of the display), adjust the level to select a “hotter” than u