The signal is then controlled via the CH-1 and CH-2 faders (4). • The XDM-343 features three microphone inputs. The Canon Mic 3 jack (10) on the front panel is for 1/4” (6.3mm) jack plugs and XLR-plugs. With the TALKOVER switch (1 1), you can attenuate all other signals without affecting the microphone volume. The XDM-343 also features two more 1/4 inch (6.3mm) Mic jacks (27, 28) on the rear panel. You can adjust the microphone volume using the CHANNEL faders. Make sure that the respective PHONO

Use ZONE 1 / ZONE 2 VOLUME (23) and ZONE BASS & TREBLE (24) knobs to control the output signal for their respective ZONES. ZONE 1 & ZONE 2 each have their own MONO/STEREO SWITCH (26). ZONE 1 output is the same as MASTER program (31), while ZONE 2 is selectable from any of the 4 channels (17) or PROGRAM MIX (PGM) (19). (26) ZONE 2 ASSIGN -ZONE 2 may be assigned to any of the 4 channels (17) or PROGRAM MIX (PGM) (19). (27) SEND CONTROL -Controls output to effects (ie. echo boxes, phasers, reverb,

A yellow LED above the power switch will glow to indicating power is ON. Be fore you turn the power on be sure you have made all connections to the mixer. Also be sure you amplifier are tuned off. Remember mixer on first and turned off last. 20. Power Supply Jack - This connection is used for your detachable AC power cord. Only connect a recommended power supply of AC 9v~12v, 500mA. Use of a power supply other than the recommend power supply may damage your unit and will void your manufactures

Note: Make sure the squelch on the receiver is turned the minimum. Microphone Set Up 1. Unscrew the bottom part of the microphone. The battery compartment is located inside of the microphone. Insert two AA batteries. 2. Screw the bottom of the microphone back into place. Connecting the Receiver Output 1. You can connect the receiver to a output source using a cable with an 1/4’’ jack or 3-pin XLR female connection. 2. Connect one end of the cable to the receiver, and the other end into the mic o

Do not permit operation by persons not qualified for operating the unit. Most damages are the result of unprofessional operation! • Do not attempt to operate this unit if the power cord has been frayed or damaged. • Disconnect from main power before making any type of connection. • Do not attempt to operate this unit, if it becomes damaged in any way. • Never operate this unit when it’s covers are removed. • To reduce the risk of electrical shock or fire, do not expose this unit to rain or moist

1. PLAYLIST - Normal / Title/ Artist / Album / Genre The DATABASE BUILDER can generate "Playlist" for USB device. You can adjust various criteria in order to filter tracks in this setting. You can turn the TRACK KNOB (21) or JOG WHEEL (16) to scroll through the different settings; " Normal / Title/ Artist / Album / Genre". See page 33 Playlist Operation. 2. REPEAT MODE - 3 different modes: Play All Repeat / Folder Repeat / Track Repeat 3. MIDI CH - Setup MIDI Channel from 1 to 16 (Deck A - Mixer

Q-SPAND PRO Featuring: User Guide and Reference Manual Q-SPAND PRO Featuring: User Guide and Reference Manual Q-SPAND PRO CONTENTS Q-SPAND PRO CONTENTS 2 ELECTRICAL PRECAUTIONS................................................................................................................4 SAFETY PRECAUTIONS........................................................................................................................5 INTRODUCTION..........................................................

Turn the knob in a clockwise direction to increase the headphone volume. 28. TRUE BASS LEVEL - This knob is used to control the amount of "TRU BASS" process is applied to the output source signal. 29. HEADPHONE JACK -This jack is used to connect your headphones to the mixer allowing you to monitor the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ headphones are rated at 16 ohm, these are highly recommended. Always be sure the Cue Level Volume (27) is set to minimum before y

Los Angeles Ca. 90040 1/08 Q-SD CONTENTS MAIN FEATURES....................................................................................................................................2 ELECTRICAL PRECAUTIONS................................................................................................................4 SAFETY PRECAUTIONS........................................................................................................................5 INTRODUCTION........................

• Only external hard drives* with external power supplies are supported. When using an ex- ternal hard drive, if you switch the Q Record "Off" and then back "On" again you will need to disconnect and then reconnect your external hard drive USB plug. If you do not do this the Q Record will not detect your connected hard drive. • If you are using a SD Card via USB SD Card reader, you must remove the USB SD Card reader first to change SD Card's. Please do not remove the SD Card from the USB SD Card