You can also visit DESA’s technical service web site at 3. Align shim under adjusting plate as shown in Figure 1. 4. Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 1). 5. Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 1). 6. While firmly holding edges of trim together, tighten both screws on the adjusting plate using a slotted screwdriver. 7. Repeat steps 2 through 6 for other side. 8. Place the assembled trim

Burner orifice clogged pilot is lit 2. Inlet gas pressure is too low 3. Thermopile leads disconnected or improperly connected 4. Burners will not come on in remote position 1. Clean burner (see Cleaning and Maintenance, page 18) or replace burner orifice 2. Contact local propane/LP or natural gas company 3. Reconnect leads (see Wiring Diagram, page 26) 4. Replace battery in transmitter and hand-held remote Delayed ignition burner 1. Manifold pressure is too low 1. Contact local propane/LP or nat

Side View Front View Top View 12" Minimum 12" Minimum 48" Minimum Ceiling Side Wall Side Wall Front of Stove Unit Side Wall Side Wall 12 " Minimum 12 " Minimum 6" Minimum 48" Minimum Ceiling Floor Back Wall Corner Wall Wall 6 " Minimum 6 " Minimum Figure 4 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on Model) Continued 104463 7 VENT-FREE NATURAL GAS STOVE HEATER INSTALLATION Continued STOVE CAVITY ASSEMBLY 1. Lift off corrugated box enclosing stove body crating. 2. Remove

This is common with most heaters. If just after burner is lit or shut off tracting while cooling noise is excessive, contact qualified service person Heater produces unwanted odors 1. Heater burning vapors from paint, hair 1. Open window and ventilate room. Stop spray, glues, cleaners, chemicals, new using odor causing products while heater carpet, etc. (See IMPORTANT state-is running ment above) 2. Gas leak. See Warning statement at 2. Locate and correct all leaks (see Check- top of page ing Ga

WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position. Pilot Burner Ignitor Electrode Figure 25 - Pilot No Control Options) 14 104461 Remote Selector Switch in Remote Position (Optional Remote Control) ON OFF REMOTE OFF PILOT ON LO IH ON OFF REMOTE OFF PILOT ON LO IH OWNER’S MANUAL OPERATING HEATER Continued TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Tu

See Lighting Instructionson page 14. 1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the remote selector switch to the REMOTE position. Note:The burners may light if handheld remote ON button was on when remote selector switch was last turned off. You can now turn the burners on and off with the handheld remote control unit. IMPORTANT: Do not leave the remote selector switch in the REMO

If the fire is on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed. TO UNLOCK press both buttons together on hand-held remote control until the light stops flashing. The hand-held remote is now un locked. Control Button Turns Burners On and Off Figure 23 - On/Off Hand-Held Remote Control Unit (GHRCB) THERMOSTAT SERIES (MODEL GHRCTB) The hand-held remote can be operated using either the manual mode (MANU) or thermostatic mode (AUTO)

Make sure middle section at bottom of log is seated into "U" shaped cutout in center of heater base. Log will fit securely on base. IMPORTANT: Make sure log does not cover any burner ports and does not touch the stove cavity (see Figure 13). 5. Fasten back panel to stove with four (4) M6 x 1bolts and washers. 6. Place freestanding stove in desired position in room. Be sure to maintain clearances to combustibles as outlined on page 8. CAUTION: After installation and periodically thereafter, check

Ventilation Air From Outdoors Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/ NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts. IMPORTANT: Do not provide

weather stripping has been added on openable windows and doors and c. caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings. If your home meets all of the three criteria above, you must provide additional fresh air. See Ventilation Air From Outdoors, page 6. If your home does not meet all of the three cr