1700, Leon-Harmel, Quebec (Quebec) G1N 4R9 Tel : (418 ) 527-3060 Fax : (418 ) 527-4311 READ AND KEEP THIS MANUAL FOR REFERENCE INTRODUCTION Stove Builder International, one of the most important wood stove and fireplace manufacturers in North America, congratulates you on your purchase and wishes to help you get maximum satisfaction from your wood stove. In the pages that follow, we will give you advice on wood heating and controlled combustion as well as technical specifications regarding insta

• Roof guys (if required) Stove pipe • An adequate number of stove pipe sections. • A 90o elbow Typical installation through the wall FIGURE 2.2.1 (A) Typical installation through the wall 1-Start by positioning your stove where you would like it to go, taking into account the minimum clearances to combustible material. You will then be able to determine where the chimney will pass through the wall. You will probably have to adjust the stove position slightly to ensure that your chimney will run

A draft measure of less than .05" w.c. will cause operational difficulties while too much draft (greater than .10" w.c.) will result in over-firing of the stove. This can result in excessive operating temperatures. 2.5 OUTSIDE COMBUSTION AIR It is recommended to install 5’’ outside air intake in the room where the stove is located or nearby. The following are signs that a fresh air kit may be required: • Your stove does not draw steadily, smoke rollouts occur, wood burns poorly, or back-draft oc

An example of the energy values of some common wood fuels found in North America is given in the following table: Wood species Energy yield (millions of BTU/cord) High energy yield Oak 29 Sugar Maple 28 Beech 26 Yellow birch 25 Ash 24 Elm 23 Medium energy yield Larch (Tamarack) 23 Red Maple 23 Douglas red fir 23 Silver birch 22 Alder 18 Poplar 17 Hemlock 17 Low energy yield Spruce 17 Pine 17 Bass 16 Fir 13 High energy yield Oak 29 Sugar Maple 28 Beech 26 Yellow birch 25 Ash 24 Elm 23 Medium ener

OWNER`S MANUAL OIL BURNING STOVE EVEREST Verified and tested following CAN/CSA B140.3 et UL 896 standards by: Intertek Testing Services Manufactured by: 1700 Leon-Harmel Quebec, (Quebec) G1N 4R9 tel : (418 ) 527-3060 Fax : (418 ) 527-4311 READ THESE INSTRUCTIONS AND SAVE FOR REFERENCE TABLE OF CONTENT TECHNICAL DATA.........................................................................................................................................1 INSTALLATION INSTRUCTIONS..................

If problem persists, contact your dealer. FUSE Branchement electrique_Page_2 5. ELECTRICAL DIAGRAM FIGURE 24 COMPOSANTES-AN.jpg pc board C:\Documents and Settings\ngagnon\Bureau\carte.bmp FIGURE 25 FIGURE 26 5.1. FUSE ACCESS All fuses are located inside the pc board box, you must remove the pc board cover to access the fuse. To do so, simply remove the 5 screws securing it in place. Make sure you put the pc board box back in place before you restart the unit. FIGURE 27 6. REPLACEMENT PARTS Conta

There should never be more than two 90 degrees elbow in the smoke exhaust system. Installation of a "barometric draught stabiliser" (fireplace register) on a smoke exhaust system is prohibited. Stove Pipe TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY: ROOF FLASHING18" CLEARANCEWALL SUPPORTWALL RADIATION SHIELDRAIN CAP Wall installation CEILING SUPPORTRADIATION SHIELD Vertical installation MASONRY CHIMNEY: Clay liner Thimble Clean out door FACTORY BUILT THIMBLE: BRICK THIMBLE: WOOD STOVE UTILISATIO

(agence de protection environnementale américaine), méthode 28. Refer to instructions manual All Drolet EPA stoves are approved by ITS (Intertek testing services) according to ULC S-627, UL 1482 and EPA (Environmental protection Agency) method 28 standards. u Détaillant autorisé: Authorized dealer: Fiche technique Technical data Type de combustible - Combustible type : Bois - Wood Surface recommandée (pi2/m2) - Recommended surface (ft2/m2) : 500 à/to 2 000pi2/ft2 (46 à/to 186 m2) Combu

Your Drolet insert will attain its best performance if installed with a chimney that generates its own draft. The minimum requirement of a flue will be the installation of a flue connector (the liner must conform to UL1777 chimney liners) from the insert into the first flue tile of the chimney (USA), see Figure 2.3 , or a continuous stainless steel liner (the liner must conform to the Class 3 requirements of CAN/ULC-S635) directly connected to the flue outlet (Canada), see Figure 2.2. A continuo