Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
If the water pipes are new or have not been used for an ex tended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Warning The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be reused. Anti-Flooding protection (for some models) The dishwasher is equipped with a system that stops the supply of water in the event of a problem with the water supply hose, or leaks within the unit, in order to prevent damage to your home. If for any reason the box containing the electrical components happens to get damaged, remove the plug for the appliance from the socket immediately. In order to guarantee that the anti-flooding feature operates properly, the "A" box with water supply hose must be attached to the water supply tap as shown in fig.B. No other type of connection is acceptable. The water supply hose must not, under any circumstances, be cut, as it contains electrical parts which are live. If the length of the hose is not adequate to make a proper connection, the hose must be replaced with one which is long enough. This hose is available upon request from specialised retailers and service center. Drain hose connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. If necessary, fit a syphon trap (U-bend) with a connecting piece for the drain hose (fig.C). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. fig.C Attention: The connecting piece for syphon trap (U-bend) must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is correct for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the whole cable, rather than using adaptors or the like as they could cause overheating and burns. Caution: The dishwasher plug must be accessible even when the appliance is installed as a built-in unit so that maintenance can be done safely. How to remove the top of your dishwasher Please follow below pictures step by step. 100-150mm Getting to know your dishwasher Close-up view (control panel) A K J DW15-PFE1** DW15-PFE2** CEH K A BD FG J A ON-OFF Button F Time-remaining Indicator BG Low Salt Indicator " 1/2 " Button Low Rinse Aid Indicator C " 1/2 " Indicator H DJ Programme Button Delayed Start Button K Programme Indicator E Delayed Start Indicator Models explanation Model Colour DW15-PFE1 White DW15-PFE1ME Silver DW15-PFE1SS Stainless Steel DW15-PFE2 White DW15-PFE2ME Silver DW15-PFE2SS Stainless Steel You can select dishwasher with big handle or without big handle according to requirement. Dishwasher interior a e d f g h i j k l b c a Upper Rack g Salt Container Cap b Lower Rack h Washing Filter c Top Spray Arm i Detergent and Rinse Aid Dispenser d Silverware Basket j Water Inlet Hose e Third Sprayer k Drain Hose f Bottom Spray Arm l Power Supply Cord How to fill the salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the salt into the container Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: For DW15-PFE1** According to the “Water Hardness Tabel”, you can calculate the time of use , then load the salt . Remove the lower rack and then unscrew and remove the cap from the salt container. If you are filling the container for the first time, fill it with water. Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. Carefully screw the cap back on. For DW15-PFE2** When the low salt indicator “1” lights, you must fill the salt. Remove the lower rack and then unscrew and remove the cap from the salt container; If you are filling the container for the first time, fill it with water; Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. Carefully screw the cap back on. 1 Important To prevent the formation of ru...
Este manual também é adequado para os modelos :Máquinas de lavar louça - DW15-PFE2 (366.89 kb)