Assessments - 1, GPA: 4 ( )

Fabricante : Manitowoc Ice Arquivo Tamanho: 2.34 mb Arquivo Nome : Língua de Ensino:

6. Remove top cover from float reservoir. QF2300 Shown Float Valve Removal 1. Place the toggle switch in the OFF position, turn off the water supply and disconnect electrical power to the ice machine. 2. Disconnect water supply line at float valve quick disconnect by depressing stainless steel lever. 3. Remove water float valve coil. 4. Depress coil and rotate 1/4 turn counterclockwise. 5. With coil wires attached, lift coil off enclosure tube. 6. QF0800/QC0700/QF2300 ONLY Rotate quarter turn fasteners counterclockwise. 7. QF0800/QC0700 ONLY Remove cotter key and pin from ice chute. 8. Remove top cover from float reservoir. 9. Lift float valve out of float reservoir. QC700/QF800 Shown 2 3, 4, 5 6 SV1791 FLOAT VALVE SV2015 Ice Machine Operation Section 3 3-14 Part Number 000002688 Water Reservoir Removal 1. Place the toggle switch in the OFF position and turn off the water supply to the ice machine at the water service valve. 2. Disconnect water supply line at float valve quick disconnect by depressing stainless steel lever. 3. Place the toggle switch in the ICE position. The dump valve will open and the float reservoir will empty. 4. After the reservoir is empty, place the toggle switch in the OFF position and disconnect power to the ice machine at the service disconnect. 5. Remove water float valve coil. A. Depress coil and rotate 1/4 turn counterclockwise. B. With coil wires attached, lift coil off enclosure tube. 5. QF0800/QC0700 ONLY Rotate quarter turn fasteners counterclockwise. 6. QF0800/QC0700 ONLY Remove cotter key and pin from ice chute. 7. Remove top cover from float reservoir. 8. Lift float valve out of float reservoir. 9. Disconnect the drain lines from reservoir. 10. Lift reservoir off of evaporator assembly. QC700/QF800 Shown Ice Diverter Removal QF0400 1. Place the toggle switch in the OFF position, turn off the water supply and disconnect electrical power to the ice machine. 2. Remove thumbscrews and lift panel forward. 3. Remove bin level sensor from white plastic panel. 4. Remove ice diverter from bin. 5. When the bin level sensor is reinstalled the correct position is 4.5” (114 mm) from the left edge of the white panel. WATER RESERVOIR EVAPORATOR ASSEMBLY SV2024 3 2 SV2052 LOCATE BIN LEVEL SENSOR 4.5” FROM EDGE OF WHITE PANEL Section 3 Ice Machine Operation Part Number 000002688 3-15 Ice Chute Removal QC700/QF800 1. Follow steps to remove float reservoir. 2. The ice chute and ice chute grommet will be removed as a unit. Pull forward on the top of the ice chute, and slide the ice chute and grommet off the end of the evaporator spout. 3. Remove evaporator spout insulation. 4. Lift ice chute out of the base. 5. Remove insulation from the bottom of the ice chute. 6. Remove bin level sensor (stainless steel plate) from ice chute. (Bin level sensor can be disconnected from the control board for complete removal from the ice machine.) NOTE: Clean and sanitize the base and all ice chute components before reinstalling. QF2300 1. Place the toggle switch in the OFF position, turn off the water supply and disconnect electrical power to the ice machine. 2. Remove ice chute retaining clamp from top of evaporator. 3. Remove vinyl hose from ice chute spout. 4. Follow steps to remove water reservoir. 5. The ice chute elbow and the ice chute will be removed separately. Support the ice chute and pull forward on the elbow to remove. 6. Lift ice chute out of the base, tip bottom forward and remove bin level sensor (stainless steel plate) from the top of the ice chute. (Bin level sensor can be disconnected from the control board for complete removal from the ice machine.) 7. Remove insulation from ice chute elbow and ice chute base. 8. Remove evaporator spout o-ring. NOTE: Clean and sanitize the base, spout and all ice chute components before re-installing. 2 3 4 5 6 SV2011 SV1787 4 2 5 6 3 8 7 Ice Machine Operation Section 3 3-16 Part Number 000002688 Bin Door Removal QF0400 Door removal allows easier access for cleaning and sanitizing. 1. Disconnect the electrical power to the ice machine and remove ice from bin. 2. Grasp the rear of the bin door and pull bin door forward approximately 5”. 3. Slide bin door to the rear while applying upward pressure (the rear door pins will ride up into the track slot). 4. Slide the rear door pins off the end and then below the door track. Slide bin door forward allowing the back of the door to lower into the bin. Continue forward with the bin door until the front pins bottom out in the track. 5. Lift the right side of the bin door until the front pin clears the track. 6. Remove door from bin. Cabinet Removal QF0400 1. Remove all ice from bin and disconnect power. 2. Remove thumbscrews and evaporator panel. 3. Remove three screws from the bottom of the left and right side of cabinet. 4. Remove nine screws from back panel. 5. Disconnect drain line clamp. 6. Slide cabinet forward and remove from base. Track Slot Slide Door Forward SV2068 Press Down to Release Door Remove 3 Sc...

Baixe o seu

Para fazer o download, introduza 2 dígitos :