Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
8. Route free end of tube to evaporator port. 9. Slip a hose clamp in free end of tube. 10. Push free end of tube on evaporator port and tighten clamp, making sure clamp is positioned on evaporator side of flange (no flange on MFD400 series flake icemaker). 11. Position ice tube under float bracket retaining tab. 12. Carefully slip ice level control stat alongside transport tube through both grommets and down into bin. 13. Run ice level control stat down through one side of cap tube fasteners attached to ice transport tube, form a 180° bend at end of tube and run back up through fastener (Fig. 1). 14. Adjust loop length to provide desired ice level. Loop must below end of ice transport tube. 15. Carefully bend end of cap tube to prevent it from slipping out of clamp. Fig. 1 Fig. 2 – Replacing existing icemakers bin top bin top top view shown ice transport tube ice level control 2.5" Apply supplied gasket to bin top stat fastener (64mm) as shown. Position icemaker on bin top. ice level control stat existing gasket add gasket front of icemaker Before turning power on 1. Clean and sanitize ice storage bin in accordance with cleaning procedure in ice storage bin installation information packed with ice storage bin. 2. Turn water to icemaker on. 3. Remove cover on float reservoir. 4. Push down on float to force water out overflow tube and into evaporator drain pan. 5. Check that water drains freely from evaporator drain pan. 6. Lift float and check that float valve shuts off incoming water when raised. 7 After turning power on 1. Turn power to icemaker on and confirm that gearmotor, compressor and fan motor start immediately. 2. Check that ice begins to enter bin within approximately 10 minutes. 3. With icemaker running, check that float reservoir water level is approximately 3/8" (10mm) below internal overflow and adjust to this level (raised line on side of reservoir) if necessary. 4. After making ice for 10 minutes, put ice against ice level control stat cap tube and check that icemaker shuts down. 5. Warm ice level control stat with your fingers and check that icemaker restarts in approximately 20 minutes. (Bin must be calling for ice.) Satellite-fill icemaker installation procedure (models MCD400A/WHS and MCD400A/WVS) Satellite-fill icemaker performance is very sensitive to the quality of installation. To ensure proper performance, ease of service and warranty coverage. it is critical that you follow the requirements detailed in this manual. If you can not meet these requirements or have questions, call our technical service group immediately at (800) 523-9361 or (610) 252-7301. Installing Satellite-fill icemaker and rough-in utilities without optional slide-out accessory The requirements below are for icemaker installation without the Follett slide-out accessory. These procedures ensure that the icemaker can be easily removed as one unit for cleaning and maintenance. For installation with the slide-out accessory, refer to instructions to install icemaker and rough-in utilities with optional slide-out accessory. General requirements Front of icemaker free of obstructions, plumbing lines, electric conduits. 12" (305mm) minimum clearance above icemaker for access to icemaker components. 6" (153mm) minimum clearance between exhaust side of icemaker and adjacent equipment. Do NOT weld icemaker to counter channels. Large, removable panels in counter face to allow icemaker removal. Machine stand accessory required for icemakers not supported on counter channels. Connection requirements Compression fittings for water and drain lines. Separate drains for condenser and icemaker. Do NOT connect drains. 20 amp power supply with 6 feet. bin signal from dispenser to icemaker water shut off compression fittings for water and drain lines separate power to icemakerseparate power to dispenser 12" 305mm clearance front of icemaker clear Note: Diagram intended as guide only. All field wiring to be installed in accordance with NEC and local electrical codes. 8 Field wiring diagrams for Satellite-fill icemaker installations All field wiring must be installed in accordance with NEC and local electrical codes. Field wiring diagram is intended only to aid electrician or technician in understanding how equipment works. Should local codes require a hard-wired connection and/or shielded wiring, eliminate the cord and plug(s) and follow the appropriate field wiring diagram. MCD400A/W and R400A/W icemakers have separate power supply from dispenser. Electric disconnects required within 10 ft (3m) for all hard-wired connections. Recommended junction box preparation of hard-wired Satellite-fill icemakers. 1. Cut plugs from supplied power cords. 2. Replace upper (power) strain relief with a cord connector. 3. Mount two 2" x 4" junction boxes using supplied holes in icemaker face. 4. Make power and bin signal connections. 25, 50 or 110 ice and water dispenser with ONE Satellite-fill icemakers (dispenser models 25CR400A/W, 25HR400A/W, 50CR40...
Este manual também é adequado para os modelos :Outros aparelhos de cozinha - D400A/W (1.85 mb)
Outros aparelhos de cozinha - MCD400A/W (1.85 mb)
Outros aparelhos de cozinha - R400A/W (1.85 mb)
Outros aparelhos de cozinha - T400A/W (1.85 mb)