Model Number: Model Description: *Product you purchased may vary from picture shown* CAUTION: Read and follow all Safety Rules and Operating Instructions of this product. Retain this document for future reference. Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA • DO NOT stand on this product. You may fall which may cause personal injury. • WEAR SAFETY GLASSES AND GLOVES when cutting the banding material. The bands may snap which may cause personal injury. • WEAR SAFETY GLASSES when removin

WARNING: There is a danger of static electricity building up in the dust collector system and causing a flash explosion or fire. To prevent static electricity buildup, install grounding kit. • A grounding kit is included and must be installed in the shop dust collector system to protect against electrostatic discharge. The grounding kit is more easily installed as the individual sections for each machine are assembled. LAYOUT SYSTEM AT SELECTED SITE Temporarily assemble the pieces together as de

Feeding the tool in the wrong direction, causes the cutting edge of the bit to climb out of the work and pull the tool in the direction of this feed. If the workpiece or bit becomes jammed or bogged down, turn the tool “OFF” by the switch. Wait for all moving parts to stop and unplug the tool, then work to free the jammed material. If the switch to the tool is left “ON” the tool could restart unexpectedly causing serious personal injury. Do not leave a running tool unattended, turn power off. On

unit the and line up with lock. Insert • Remove (4) screws holding top in the lock rod into the back of the lock. Chain place. • Test lock operation. Lever Style -Lift or • Lift top off of unit enough to reach the • Reinstall drawers. lower (depending on the wiring harness. slide) the release lever • Reinstall work surface. • Disconnect wiring harness from unit. • Reconnect power to the unit. on both sides, (this allows the slides to ride • Remove top from unit. over the stops.) Pull out to remo

• Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. Move actuator rod for access. • Remove (4) screws holding top in place. • Lift top off of unit enough to reach the wiring harness. • Disconnect wiring harness from unit. • Remove top from unit. Press to release Chest Top Installation • Connect wiring harness to top. • Position top on unit. • Attach using (4) screws. • Make s

• Safety • Assembly • Operation • Service • Maintenance • Espa5ol Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A. Printed in U.S.A. 770-10032A (8/99) Content Page Warranty Information......................................... 2 Safe Operation Practices................................... 3 Accessories ....................................................... 6 Assembly ........................................................... 7 Operation ..................................................

Together, the two gear sections create a large volume flow which produces rapid cylinder movement under low load conditions. Above unloading pressure, a pilot pressure line(which simulates actual pressure at the cylinder) activates the unloading valve, which causes the flow to bypass the large gear section and return to the pump inlet area. The small gear section is now operating alone, and will generate the higher pressure necessary for the actual log splitting operation. The original factory

247.346250 Caution: Read and Follow All Safety Rules and Instructions Before Operating This Equipment CRAFTSMAN® 5.0 HORSEPOWER 25.5 TON HYDRAULIC LOG SPLITTER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A. IMPORTANT SAFETY RULES A THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL I

320.48291 CAUTION! Before using this • Safety product, read this manual and , Operation follow all its Safety Rules ° Magstlc ® and Operating Instructions. ° Maintenance Sears Brands Management Corporation www, craftsman.com Warranty Page2 Safety instruction Page3 Description Page4 Operation Instructions Page6 Applications Page 11 Maintenance Page 14 Troubleshooting Page 15 Parts List Page 15 ONE YEAR FUt.L WARRANTY ON CRAFTSMAN®PRODUCT If this Craftsman product fails due to a defect in material

Figure 7 -Attaching Inlet ATTACH HOSE Refer to Figure 8. Hose needs to be attached to the inlet using hose clamp. To attach hose: • Slide hose clamp onto one end of hose. Loosen clamp screw if required to slide hose clamp onto hose. • Position the hose clamp wires on the hose grooves. • Slide hose with clamp onto inlet. • Tighten hose clamp screw to secure hose with inlet. • Slide other hose clamp onto the opposite hose end. This end will be connected to the dust producing machine Figure 8 -Atta