Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Then insert the handgrip (11) in the suction tube. Attach the delivery tube (19) to the flexible hose (13) by means of the plastic clips. Then insert the flexible hose (13) in the suction socket (8) in such a manner that the markings on both correspond and the button audibly clicks into place. (Q Subsequently, insert the delivery tube (19) firmly into the coupling piece (5) on the motor block (2). Now attach the second suction tube (the one with fixture studs) to the p suction tube which is already mounted. Attach the spray-extraction carpet shampoo nozzle (18). Attach the delivery tube (12), which is mounted on the nozzle, by the coupling piece (39) to the spray diffusor control (17) and secure by turning the coupling piece (39). Then press the delivery tube (12) into the sclamping fixtures on the suction tubes. The control knob on the appliance must be set at "0". © Plug the appliance into a mains socket. The appliance is now ready for use. Switching on the appliance Turn the control knob (7) to the „spray-extraction" symbol. The pump lamp (6) should now be lit up. The spray-extraction system: • sprays pressurised jets of cleaning solution • breaks down dirt and cleanses deep into the fibres • extracts dirty water powerfully and lifts up carpet pile. All in a single operation. direction of work sprays extracts and dissolves and cleanses © Place the spray-extraction carpet shampoo nozzle on the carpet in a corner of the room. Press the control trigger (4) on the handgrip (11) until cleaning solution sprays onto the carpet. Then slowly draw back the upright nozzle in a straight line over the carpet. On completion of a lane or when interrupting operation, release the trigger to stop the jet spray flow of cleaning solution. When the sprayed on liquid has been vacuumed off, raise the nozzle and, with a slight overlap, begin a new lane. In this way, the entire area can be covered strip by strip. If there are still traces of liquid on the cleaned strip of carpet, these areas can be vacuumed over again, but make sure that the trigger control (40) is released! As the upper part of the nozzle is transparent, you can judge for yourself by the colour of the extracted water when to end the spray-extraction process. Badly soiled areas can be pre-treated by turning the control knob to the „spray only" position. Aim the nozzle at the area to be treated and press the trigger control to emit a jet spray of cleaning solution. Leave to work in for a short time, then spray-extract as described above (remember to turn the control knob back to the „sprayextraction" position U). Take care not to spray too much fluid onto the carpet as this can result in ripples or lumps forming, which only disappear again after a prolonged drying period. When vacuuming liquids, avoid spilling the residual liquid in the vacuum hose or tube by holding the hose or tube up with the motor still running, and then switch off. Important! • If the carpet has been shampooed before, there may occur a stronger foam development during the first use of your spray-extraction system. Should foam emerge from the air outlet, switch off the appliance and empty the collecting bin. To avoid further development of foam, add one cup of vinegar into the collecting bin. Increased development of foam is impossible after having used the THOMAS 4 IN 1 with its Original THOMAS ProTex cleaning solution for one time, since it includes a special foam stopper. • Do not walk on the carpet while it is still damp. Washing hard floors (W Slide the hard floor adaptor (22) onto the sprayextraction carpet shampoo nozzle (18). Now you can wash and dry smooth ceramic, stone, synthetic or wooden floors in one single operation. Upholstery shampooing To shampoo upholstery or car seats, use the spray-extraction upholstery shampoo nozzle (20). Take care not to apply too much fluid to upholstery as, depending on the type of padding, a lengthy drying period can be expected. The spray-extraction upholstery shampoo nozzle (20) is fitted directly onto the spray diffusor control (17). The delivery tube is secured at the valve by turning the coupling piece (39). Detach the delivery tube (12) by turning the coupling piece (39). Operate as described under "Carpet shampooing". After spray-extraction cleaning Pull out the plug. Before removing the motor block (2), detach the delivery tube (19). ©Remove the vacuum cleaner's motor head (2) and place onto shallow container to avoid getting the intended surface dirty from residual water. 17 Take out the extraction liquid tank (28) and empty. (Any unused cleaning solution can be stored in a suitable receptacle.) Empty the collecting bin (1) and wash out thoroughly. (O Care for the pump and valves by filling the extraction liquid tank with clear water, putting it in the collecting bin and replacing the motor block (2). Operate the spray-system on a smooth floor or over the sink. Subsequently, clean both recept...
Este manual também é adequado para os modelos :Aspiradores - Super 30S (813.1 kb)
Aspiradores - Compact 20 (813.1 kb)
Aspiradores - Compact 20S (813.1 kb)