Assessments - 5, GPA: 4.8
(
)
)
|
Facilidade de uso
brush rim is retracted: set the lever at the symbol . Dry vacuuming Assembly ©Pull out the plug and lift off the motor block (2). Then push the cleaning solution tube (37), which is located in the motor block (2), into the fixture provided for this purpose (36). Inserting the filter First mount the foam filter (26), the the protective paper filter (27) and the clamping ring (25). Secure by means of the pre-mounted swivel clips (31). Place the filter bag (34) inside the collecting bin, making sure that the opening located in the cardboard inlay (35) is placed in line with the suction socket (8). Then press the filter bag evenly around the sides of the collecting bin. Put the motor block (2) back in position. The control knob on the appliance must be set at "0". © Plug the appliance into a mains socket. Switching on the appliance /M When using the appliance in the dry vacuuming mode, the control knob (7) must be set at the „carpet + floor nozzle" symbol. Upholstery nozzle Used for vacuuming upholstered furniture, mattresses, and small uneven surfaces. The nozzle's thread catcher also allows you to vacuum threads and fluff. For easy handling the upholstery nozzle can also be used with only one section tube, or directly on the hose's grip. Joint nozzle Used for thoroughly vacuuming corners, grooves, joints and other tight places. The joint nozzle can also be directly attached to the grip. Storage and transport Set the control knob at "0" and pull out the plug. Coil the mains cable loosely in the hand and hang it over the notch in the carrying handle. The suction tubes, complete with nozzle and flexible hose, can be hooked into the fixtures at the back of the appliance. The pilot lamp (6) should not be lit up. The appliance is ready for use. Wet vacuuming Assembly ©Pull out the plug and lift off the motor block (2). Warning! Always remove the filter unit before vacuuming liquids, as it will otherwise become unserviceable (see section "Changing the filter"). Always ensure that the float (38) is kept clean and in good condition. It acts as a safety device and automatically interrupts the flow of air when the collecting bin is full. 15 Put the motor block (2) back in position. The control knob on the appliance must be set at "0". © Plug the appliance into a mains socket. Switching on the appliance ©When using the appliance in the wet vacuuming mode, the control knob (7) must be set at the "carpet + floor nozzle" symbol. The pump lamp (6) should not be lit up. The appliance is ready for use. Liquids can be directly vacuumed out of containers with either the vacuum hose or the hose with a section. Take care when vacuuming liquids from high-sided containers or basins, where the quantity level exceeds the liquid capacity of the collecting bin. Remember that, in such a case, the liquid will continue to flow from the container even if the collecting bin is full and the float has stopped the suction flow of the appliance. Therefore, vacuum only small quantities of liquid at a time and empty the collecting bin before switching on again. Always lift the suction tube out of the liquid before switching off the motor. Warning! If petrol, paint thinner, fuel oil etc. are allowed to mix with the suction air flow, explosive fumes or compounds may be formed. Acetone, acids and solvents may attack the materials on your appliance. It is quite safe to vacuum water which contains ordinary household cleaning agents. After vacuuming liquids, the collecting bin and all accessories used should be wiped clean and left to dry. Operating the spray-extraction system Before spray-extraction cleaning Make sure that what is to be cleaned by sprayextraction is suitable for this purpose. Do not use the appliance for delicate, hand-woven or non-fast carpets. Test the colour-fastness of your carpet by pouring a little cleaning solution onto a white cloth and rubbing this onto a normally hidden section of the carpet. If there are no traces of dye on the cloth, it can be assumed that the carpet is colour-fast. However, if dye comes off onto the cloth, do not clean the carpet by spray-extraction. If you are in doubt, contact a specialist dealer. Before shampooin g your carpet, vacuum-clean the whole area thoroughly. Ensure that the room is well-aired during and after spray-extraction cleaning to enable the carpet to dry quickly. 16 Carpet shampooing ®Pull out the plug and lift off the motor block (2). When using the appliance in the spray-extraction mode, ensure that the extraction liquid tank (28) is inserted in the collecting bin. (N Pour the cleaning concentrate into the sprayer tank (28) and fill up with water. (Observe the dosing instructions on the lable of the Protex bottle.) Use lukewarm water (max. 30°C) only. Higher temperatures can damage not only the appliance, but also the carpet and upholstery. Detach the cleaning solution tube (37) from its fixture in the motor block (2). © While p...
Este manual também é adequado para os modelos :Aspiradores - Super 30 (813.1 kb)
Aspiradores - Compact 20 (813.1 kb)
Aspiradores - Compact 20S (813.1 kb)