Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
it can clear blocked sinks and drains. With only a few simple accessories, it can be used for shampooing your carpets or upholstery. The THOMAS 4 in 1 is a multi-purpose product. In conjunction with the cleaning solution, the sprayextraction function enables you to clean carpets, upholstery and hard floors. The wet vacuuming mode is suitable for picking up water-based liquids only and it should never be used for vacuuming inflammable liquids. As a vacuum cleaner, it is intended for the removal of dry dirt and dust from carpets, floors, furniture and curtains. Unpacking the appliance Unpack the appliance from the carton, remove any packaging and identify the following parts and functions in the diagrams at the beginning of this booklet to gain a better understanding of the instructions given below. The letters indicated below refer to the diagrams on pages 3 and 5. Assembly instructions Assembling the THOMAS 4 in 1. The parts required for the chassis are to be found loosely packed in the carton. Assembling the castor wheels Undo the snap-on fasteners (3) and lift off the motor block (2). Take out the extraction liquid tank (28) and cleaning solution. Turn the collecting bin (1) upside down, i.e. with the opening facing the floor. fy To facilitate assembly, we recommend lightly greasing the pegs at both ends. First insert the pegs (30) in the base of the collecting bin (1), then push them in, together with the castors, as far as they will go. Fitting the motor block (D Place the motor block (2) on the collecting bin (1), making sure that the surfaces of both parts correspond. Secure the motor block (2) by means of both snap-on fasteners (3). Connecting the flexible hose Insert the flexible hose (13) in the suction socket (8) in such a manner that the markings on both the suction socket and the hose connecting piece correspond and the button clicks into place. Remove the hose by turning the hose connecting piece and slowly with drawing the hose. Then attach the desired accessories. Suction tube holder The suction tubes (14) complete with accessories and flexible hose (13) can be hooked into the fixtures at the back of the appliance. Cable storage (G After use, the mains cable (1) can be wound loosely in the hand and hung over the notch in the carrying handle, as shown in the illustration. Changing the filter Always pull out the plug before changing the filter! NOTE! Hygienic filter change and emptying of the collector bin. Emptying the collector bin and change of all filter types used in the vacuum cleaner (e.g. foam-/paper filters, paper filter bags, etc.) can be done hygienically. To this end, please use the hygienic gloves included in the delivery. Replacement gloves are readily available at relevant supply stores. Motor protection filter After each wet suction and spray extraction process, check the motor protection filter (33) for contaminations and clean if required. For this, open the float valve (38) in the direction of the arrow, and take the motor protection filter from the suction opening. Replace the cleaned or new filter and then put the float valve back in place. 14 Paper filter bag Place the filter bag (34) inside the collecting bin (1), making sure that the opening located in the cardboard inlay (35) is placed in line with the suction socket (8). Then press the filter bag (34) evenly around the sides of the collecting bin (1). THOMAS paper filter bags are essential when vacuuming fine dust, e.g. soot, ashes, sawdust or cement. However, they are also recommended for normal use, as they not only improve the retention of dust, but also make filter changes more hygienic. Concentrated cleaning solution Your THOMAS 4 in 1 contains 1 Liter of ProTex cleaning concentrate. Please see bottle label for instructions for use and dosage. Use of tools and accessories Reversible carpet + floor nozzle This nozzle is suitable for vacuuming carpets and hard floors, such as stone, parquet and synthetic tiles. By means of the foot-operated lever, the nozzle can be adjusted to suit the type of floor to be vacuumed: - Vacuum smooth floors with the brush edge: set the lever at the symbol . - Vacuum carpets with the smooth edge, i.e. brush rim is retracted: set the lever at the symbol . Dry vacuuming Assembly ©Pull out the plug and lift off the motor block (2). Then push the cleaning solution tube (37), which is located in the motor block (2), into the fixture provided for this purpose (36). Inserting the filter First mount the foam filter (26), the the protective paper filter (27) and the clamping ring (25). Secure by means of the pre-mounted swivel clips (31). Place the filter bag (34) inside the collecting bin, making sure that the opening located in the cardboard inlay (35) is placed in line with the suction socket (8). Then press the filter bag evenly around the sides of the collecting bin. Put the motor block (2) back in position. The control knob on the appliance...
Este manual também é adequado para os modelos :Aspiradores - Super 30 (813.1 kb)
Aspiradores - Super 30S (813.1 kb)
Aspiradores - Compact 20S (813.1 kb)