Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
The hard floor tool provides effective cleaning for OperationHard Floor Cleaning Your deep cleaner may have come with a hard floor tool and Hard Floor Solutions Formula. The hard floor tool provides effective cleaning for Operationlinoleum, vinyl, and tile floors. Caution: Do not use on unsealed hardwood floors. 1. Thoroughly vacuum or sweep floor to pick up any debris. NOTE: Prior to filling with formula and water be sure all carpet cleaning formula is thoroughly rinsed from tank. 2. Fill BISSELL Hard Floor Solutions Formula to the indicated fill line in the built in measuring cup and pour into mouth of bladder. 3. Fill the bladder with clean hot tap water and set aside. 4. 4. Attach the hard floor tool to the bottom of the machine by hooking it into the nozzle and swinging it down until it clicks into place. 5. Be sure the ReadyTools dial is set to FLOOR CLEANING. 6. Plug into an outlet and turn the power ON. 7. Plan your cleaning route to leave an exit path. Be sure to allow adequate time for floors to dry. 8. While pressing the spray trigger, make one slow forward wet pass and another back. Caution: Do Not Overwet. 9. Repeat the motion without pressing the trigger using the hard floor tool to squeegee and suction up the dirty water. 10. When finished, remove hard floor tool, rinse and let dry before storing. Refer to the Maintenance section on page 12 for machine clean up and storage instructions. 11 800.237.7691 ug120-4073_1623_908.indd 11 10/14/08 12:59:40 PM Maintenance and care Machine care For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. 1. Turn power switch OFF. Unplug the machine and wrap the power cord. 2. After emptying the 2-in-1 water tank, rinse it with running hot tap water, taking care to clean underneath and around the heavy duty bladder. Clean out red lint screen. Removable nozzle may be rinsed if necessary. 3. Replace the 2-in-1 water tank on the machine. 4. Any loose hair or debris can be pulled from the brush roll and thrown away. 5. To clean attachments, remove from hose and rinse in clean, running water. Dry before storing. Clean the hose by suctioning clean water from the tap. Before wrapping back on machine, lift end of hose and stretch out to ensure all water is cleared from hose. Refer to page 10, illustrations 11 and 12. 6. Wipe the machine’s exterior with a soft cloth. 7. After carpet is dry, vacuum again to remove hair and fuzz. Machine storage Put the unit away in a closet or basement for the next use. Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. 12 800.237.7691 ug120-4073_1623_908.indd 12 10/14/08 12:59:40 PM WARNING: To reduce the risk of fire, electric shock or injury, unplug from theoutlet before servicing. Remedies 1. Turn power switch OFF; Refill bladder with clean hot tap water. 2. Turn power switch OFF; remove tank and reseat tanks. 3. Turn power switch OFF; after 1 minute turn ON and depress spray release trigger. Turn power switch OFF and unplug from the outlet. To check if a pump belt has broken, you will need a flat head screwdriver. A. Insert the blade end into the slot of the belt access door to release. Examine the belt for breakage. You should be able to see the pump belt looped around the motor shaft. If it is broken or missing, please refer to Replacement Parts on page 14. A replacement belt may be ordered at or by calling BISSELL Consumer Services at 800-237-7691. Complete installation instructions will accompany the replacement belt. B. When replacing belt access door be sure to line up slots of belt access door with slots in machine, slide door into place and snap shut. WARNING: To reduce the risk of fire, electric shock or injury, unplug from theoutlet before servicing. Remedies 1. Turn power switch OFF; Refill bladder with clean hot tap water. 2. Turn power switch OFF; remove tank and reseat tanks. 3. Turn power switch OFF; after 1 minute turn ON and depress spray release trigger. Turn power switch OFF and unplug from the outlet. To check if a pump belt has broken, you will need a flat head screwdriver. A. Insert the blade end into the slot of the belt access door to release. Examine the belt for breakage. You should be able to see the pump belt looped around the motor shaft. If it is broken or missing, please refer to Replacement Parts on page 14. A replacement belt may be ordered at or by calling BISSELL Consumer Services at 800-237-7691. Complete installation instructions will accompany the replacement belt. B. When replacing belt access door be sure to line up slots of belt access door with slots in machine, slide door into place and snap shut. Troubleshooting Reduced Spray OR No Spray Possible cause 1. Bladder may be empty 2. 2-in-1 tank may not be seated properly. 3. Pump ma...