(Adjust only those controls covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.) • If the telephone has been dropped or the housing damaged. • If the telephone exhibits distinct change in performance. SAVE THESE INSTRUCTIONS 5 TELEPHONE PART IDENTIFICATION S peak er 9 Dial K ey s M ic S tatus LE D 10 V olum e Down B utton M em ory Dial K ey 11

7. Do not mix batteries of different sizes or from different manufacturers. 6 Unpacking and Installation Box Contents The following items should be packed with your 6012. Please contact your dealer if any of them is missing. B a s e 1 H a n d s e t 1 P o w e r A d a p t e r 1 B e l t C l i p 1 L i n e C o r d 1 B a t t e r y 2 7 Telephone Part Identification LCD 9 2.5 mm Headset Jack CID Review/Volume Up 10 Hang Up Button Esc/Flash Button 11 CID Review/Volume Down Speaker Button 12 Dial Pad Answ

It is not suitable for connection to a PBX. The ringer equivalence numbers (RENs) of all instruments Do not clean any part of your Celestia connected to an exchange line must not add up to more than 4. 400 with solvent chemicals, abrasives or The Celestia 400 has a REN of 1; most other phones and fax spray cleaners which might get inside the machines have a REN of 1 unless marked otherwise. case and cause damage not covered by the guarantee. When necessary, clean it with a damp cloth. NOTE: if y

• Telephone • Handset • Handset Cord • Line Cord • 3 AA Batteries • Power Adapter • Instruction Manual BATTERY INSTALLATION The 9125 telephone requires 3 AA size 1.5 V batteries for the LCD display. To install the batteries, follow the steps below: 1. Remove the battery cover. The cover is located underneath your phone. 2. Insert 3 AA size 1.5 V batteries. Be careful to observe the polarity markings in the battery compartment. 3. Replace the battery compartment cover. DIALING MODE The 9125 dial

The cordless phone won’t work if the base unit has no electrical power. Move the handset closer to the base unit. Check the Battery Level symbol on the display. If it is low, replace the cordless handset on the charger pod to recharge the batteries. If you still can’t make calls, try re-registering the handset. “When I press Make sure the batteries are fitted in your handset. If the Battery keys on the Level symbol on the display shows ‘low’, recharge the batteries. handset, nothing happens.” Pr

When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. e. If th

If pressed during a call, activates the speakerphone. End Key - End a call. If pressed and held, powers off the handset Left/Right Soft Keyimmediately over it in the display. - Performs the function indicated by the text *Key - Press and hold to lock the keypad. Set up a conference call as described on Page 35. 16 Navigation Key Up/CID Key - Scrolls up through list and menu options. Increases the receiver or speakerphone volume during a call. Enters the CID book as described on Page 18. Down/Pho

sales receipt. (Default Remote Access PIN is 0000) . mode, the change to ANSONLY automatically, and will not allow callers to leave messages, EMC: EN 301489-01: V1.8.1 : 2008; Remember to include the mains adapter. 5. Press

CALL SCREENING .......................................................................................................................... TROUBLESHOOTING....................................................................................................................... 33 DECLARATION OF CONFORMITY................................................................................................. 34 GUARANTEE AND SERVICE.............................................................................

No display. Empty battery Recharge battery Please contact the technical support of the network provider for further information. This telephone is not equipped with an earth function! Therefore some of the functions may be limited when used in PBX systems. If the fault persists: Disconnect all other instruments connected to the same line as this, and try to make a call. Disconnect the base unit from the telephone line and plug a different phone into the master socket. Try making a call. If this