No. No. Used Description No. No. Used Description 1 911001-2 2 P.H. Screw M3x6 (With Washer) 51 251246-3 4 (+) P.H. Screw M4x5 2 * 2 P.H. Screw M4x14 52 342430-2 2 Adjust Plate 3 911228-4 2 P.H. Screw M5x18 (With Washer) 53 911226-8 2 P.H. Screw M5x18 (With Washer) 4 931106-2 2 Rivet 0-5 54 323001-4 1 Drum Rear Shaft 5 * 1 Switch 55 253139-0 1 Flat Washer 8 6 * * P.H. Screw M4x6 (With Washer) 56 211032-4 1 Ball Bearing 608ZZ (Old 210011-9) 7 682502-4 1 Cord Guard 8-85 57 961004-6 1 Retaining Rin

001606 1 2 3 4 5 001606 1 2 3 4 5 1. Bolt 2. Drum 3. Planer blade 4. Drum cover 5. Adjust plate 001607 1 2 3 4 5 6 7 8 1. Adjust plate 2. Screws 3. Heel of adjust plate 4. Back side of gauge base 5. Blade edge 6. Planer blade 7. Inside edge of gauge plate 8. Gauge plate To install the blades, first clean out all chips or foreign matter adhering to the drum or blades. Use blades of the same dimensions and weight, or drum oscillation/vibration will result, causing poor planing action and, eventual

should never be left around the work area. 7. Before using the tool on an actual work2. Avoid cutting nails. Inspect for and piece, let it run for a while. Watch for remove all nails from the workpiece before vibration or wobbling that could indicate operation. poor installation or a poorly balanced blade. 3. Use only sharp blades. Handle the blades very carefully. 8. Make sure the blade is not contacting the workpiece before the switch is turned on. 4. Be sure the blade installation bolts are s

alternating current FUNCTIONAL DESCRIPTION 002549 1 1. Knob 002553 1 2 1. Lock button 2. Switch trigger ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when releas

13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 14. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. Tool Use and Care 15. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work

SPECIFICATIONS Model 2012NB Cutting width 304 mm (12”) Max. cutting depth 3.0 mm (1/8”) of stock width less than 150 mm (5-7/8”) 1.5 mm (1/16”) of stock width from 150 mm (5-7/8”) to 240 mm (9-1/2”) 1.0 mm (3/64”) of stock width from 240 mm (9-1/2”) to 304 mm (12”) Feed rate /min 8.5 m (27.9 ft.) /min. Table size (W x L) 304 mm x 771 mm (12” x 30-3/8”) No load speed (RPM) 8,500 /min. Dimensions ( W x L x H ) 483 mm x 771 mm x 401 mm (19-1/64” x 30-3/8” x 15-25/32”) Net weight 27 kg (59.5 lbs) •

For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. 1 2 1 2 Pins 2. Edge fence (Guide rule) 1 23 1. Rear base 2. Foot 3. Planer blade 003873 Edge fence (Guide rule) Edge fence is useful for minimizing a short run of cut by cutting in a uniform width. The edge fence (guide rule) is provided on the side of the tool. Press two pins for the edge fence (guide rule) so that the ed

A loose installation bolt can be dangerous. Always check to see they are tightened securely. Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Knob Adjusting front base The front base is factory-adjusted to allow concave cuts with a radius of 320 mm. For concave cuts with the tool’s minimum radius of 300 mm, loosen the wing bolt on either side and raise the front base as far as it will go. Then retighten the two wing bolts firmly to secure t

® TtiakixCL Woodworking G 12-1/4" Planer J(P31^« Precision Engineered for an Even Cut Every Time • Powerful 15 AMP motor with 12,000 RPM • Poly"V"belt designed with grooves efficiently transfers power from the motor to the blades • Large ejection chute for high rate of chip discharge • Front roller for easy moving over rough materials • Externally accessible brushes for easier serviceability • Large,conveniently located depth setting knob for easy adjustment MODEL KP312 INCLUDES: So