Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
1. Remove plastic sleeve from gear housing shaft. 2. Be sure plate (A) remains on PTO shaft. 3. Align locking hole in upper plate with notch in edge of gear housing and insert head locking tool (B). 4. Thread line head onto shaft by turning it counter clockwise until head is tight against upper plate. B A FRONT HANDLE INSTALLATION Tools Required: Screwdriver. Parts Required: Front Handle Assembly 1. Position front handle for comfortable operation and secure screws. 16 NOTE Refer to Operation with Blades page 20 for correct Accessory / Blade equipment requirements. WARNING DANGER You must install a U-Handle/Blade Conversion Kit before operating this unit using metal blades, otherwise serious injury may result. HARNESS CLAMP INSTALLATION NOTE SRM-2601 requires installation of Harness Clamp included in the Blade Conversion Kit or U-Handle / Blade Conversion Kit. If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. 1. Remove shield and gear housing as an assembly. a. Loosen two (2) screws (A) that clamp the gear housing to the drive shaft housing. b. Remove locating screw (B) found at the top of the gear housing. Pull shield and gear housing assembly from the drive shaft assembly. A B 16 NOTE Refer to Operation with Blades page 20 for correct Accessory / Blade equipment requirements. WARNING DANGER You must install a U-Handle/Blade Conversion Kit before operating this unit using metal blades, otherwise serious injury may result. HARNESS CLAMP INSTALLATION NOTE SRM-2601 requires installation of Harness Clamp included in the Blade Conversion Kit or U-Handle / Blade Conversion Kit. If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. 1. Remove shield and gear housing as an assembly. a. Loosen two (2) screws (A) that clamp the gear housing to the drive shaft housing. b. Remove locating screw (B) found at the top of the gear housing. Pull shield and gear housing assembly from the drive shaft assembly. A B NOTE For SRM-2610 handle assembly refer to "U-Handle Installation page 18 instructions 1, 10, 12 - 16. ACCESSORY INSTALLATION Blade Conversion Kit P/N 99944200415, U-Handle / Blade Conversion Kit P/N 99944200521, Muffler Bracket Kit P/N 10099057730. IMPORTANT Prevent steel drive shaft from sliding from drive shaft housing. If shaft does slide free, clean dirt from shaft and re-assemble. 2. Remove front handle. a. Remove four (4) screws and nuts and handle support from handle. b. Remove handle. 3. Install clamp. GRASS TRIMMER/BRUSH CUTTER OPERATOR'S MANUAL GRASS TRIMMER/BRUSH CUTTER OPERATOR'S MANUAL 4. Install front handle, gear housing and shield. 5. Balance unit. a. Put on harness and attach unit to harness. b. Slide harness clamp (J) up or down until unit balances with cutting attachment approximately 2" - 3" from the ground. c. Tighten harness clamp screw. J INSTALL METAL SHIELD Tools Required: 8mm x 10mm Open End Wrench, Screwdriver. Parts Required: Metal Shield, Bracket, 3 - 5 mm x 15 mm screws w/captivated flat and lockwasher (metal shield to gear housing), 2 - 5 mm x 8 mm screws, 4 - 5 mm nuts, 4 - 5 mm lockwashers (bracket to shield and bracket to gear housing). 1. If necessary, remove nylon line head and plastic shield. 2. Loosely attach bracket (A) to shield (B) and attach to bottom of gear housing (C) with screws and nuts provided. Tighten all attaching hardware. Install Blade Tools Required: Locking Tool, scrench. Parts Required: 1 - Upper Fixing Plate, 1 - Lower Fixing Plate, 1 - 10 mm L.H. Nut, 1 - 2x22 mm Split Pin. 3. Install upper plate (D) on splined shaft. 20 mm center hole blade requires use of Upper Plate (D) with 20 mm pilot. 25 mm center hole blade requires use of upper plate (D) with 25 mm pilot. Upper plate with 37 mm pilot of the SRM-2601 should be retained for use with nylon line head. 4. Place Blade (E) over upper plate pilot, install the Lower Plate (F) and 10mm LH nut (G). Tri-Cut Blade (H) is installed with Glide Cup (J). 5. Insert Locking Tool (K) through hole in upper plate and notch in gear housing to prevent splined shaft from turning. Tighten nut and secure with Split Pin (L). SRM-2601 18 18 Tools Required: 8mm x 10mm Open End Wrench, Screwdriver, 3mm and 4mm Hex Wrench, Pliers Parts Required: U-Handle/Blade Conversion Kit P/N 99944200521. NOTE For model SRM-2610 use Steps 1, 10, 12 - 16. 1. Close choke and remove air filter cover. 2. Disconnect ignition stop leads (A) and (B). 3. Remove inner throttle linkage from carburetor swivel (D). 4. Remove throttle linkage (E) from throttle linkage fixture (F). 5. Loosen bolt (G) and pull drive shaft assembly from clutch case. 6. Loosen two (2) rear handle screws (H) and pull rear handle (I) from the drive shaft assembly. 7. Loosen four (4) screws and remove front handle (J). 8. Position lower U-Handle bracket (K) 400mm (15-3/4 in.) from engine end of drive shaft. Secure with three (3) 5mm x 30mm bolts. 9. Pos...
Este manual também é adequado para os modelos :Ferramentas para Jardim - SRM - 2610 (902.26 kb)