Assessments - 4, GPA: 4 ( )

Fabricante : Husqvarna Arquivo Tamanho: 3.02 mb Arquivo Nome : Língua de Ensino:

Delta Blades Delta blades were created primarily for overseeding existing lawn. They effectively incorporate grass seed into the soil. This is an easy, reliable method for rejuvenating poor lawns. The delta blade is also useful as a vertical mower for cutting running stem grasses and opening up the soil to oxygen, water, nutrients and other chemicals. Delta blades are also beneficial on slopes, terraces and in high clay content soils where water runoff is a problem. The blades should be set to penetrate the soil to a depth of 1/8" to ." with a maximum penetration of .". Check your seed bag for the manufacture’s recommended depth of application. Spring Tines Ideal for the established lawn that is not in need of a complete renovation but requires dethatching (dryspots, fungus, etc.). Spring tines are designed to pluck dead grass and thatch out of the lawn without tearing or damaging existing root structure. With the flexible tines, the lawn is combed only 0.5 cm into the soil, so it cannot penetrate the root structure. Spring tines provide less aggressive dethatching than flail blades. NOTE: Do not use spring tines with bagger attachment. operati on 18 IMPORTANT INFORMATION Clear the lawn of any debris. Clearly mark rocks and other fixed objects. Be especially sure to check for hidden electrical cables or similar in the surface of the lawn. Before Starting • Mow the lawn ." shorter than normal. • Allow the lawn to dry. Wet conditions can cause extensive damage to healthy grass. • Check for stones or fixed objects in the lawn. Dethatching • Set the depth lever in working position. • To engage the clutch in heavy thatch, bear down on the handle and raise the front wheels slightly. Hold the clutch engaged against the handle and carefully lower the machine into the turf. • Do a small test area at a slow walking pace. • If the engine speed drops excessively, the depth setting is too deep. If the machine pulls forward and bucks roughly, the depth setting is too deep. Finishing • Remove all extracted thatch from the grass and compost/dispose of properly. • Other methods for improving your lawn may include aeration and fertilization. 8060-016 Hold clutch bail against handle operati on 19 2 3 1 2 1 Seed Application Preparing the Lawn Cut the grass to approximately • ." (1-1.5 cm) lower than you normally would. • Do not water before sowing. • Remove the layer of old grass cuttings (thatch). • Aerate the lawn with a core-type ground aerator. • Fertilize the lawn. Seed Application Chart Located on the seeder, the chart values are approximate; quantities of seed depend on the speed at which the machine is run. Faster running speeds results in sparser sowing. To set the seed application, loosen the wingnut and turn the seeder dial to the desired sowing setting. Retighten wingnut. Pull back on the OPEN/CLOSE lever to apply seed. Seed Application Recommendations • For best results, sow in two directions with a 45° angle between. • Water generously immediately afterward and continue watering moderately for 10–14 days to keep the soil moist. • After germination, water sporadically to encourage root growth. Bagger Attachment and Removal To attach bagger, place foot on safety door rear bolt and push down until door is flat. Set the bagger onto the door and up against the chute. Secure bag clamp. To remove door, unlatch bag clamp. Push down on rear bolt and slide bagger away from the chute. The safety door is spring loaded and will flip up to cover the rear opening until the bag is reinstalled. 8060-021 1. Selection dial 2. Wingnut 3. OPEN/CLOSE lever Set application per chart and turn on seeder 8060-023 Secure bag latch 8060-032 1. Safety door 2. Rear bolt Attach bag to bagger frame MAINTENANCE Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. MAINTENANCE Daily Before Staring Maintenance interval - months/hours 1/25 3/50 6/100 12/300 Check the engine oil level . Replace engine oil 1) . Check the air filter . Replace air filter cartridge 2) . Clean sludge reservoir for fuel system . Check and clean the spark plug . Replace spark plug . Check idle speed . Check and adjust play in valves 3) . Clean fuel tank 3) . Check, replace fuel lines as necessary 3, 4) . Check clutch and clutch cable . Check flail blade lock washers . Check decals and warning signs . Check the seed holes for the seeder . Check wear and tension on the belts . Check blade wear and condition . Check the chassis, bolts and set screws . Check the seed control lever for the seeder . Check the wire mountings on the seeder . Lubrication; see the Lubrication schedule 1) First change after 20 hours. 2) In dusty conditions maintenance is required at shorter intervals. 3) Performed by authorized service workshop. 4) Performed every second year. With daily use, the machine shall be lubricated twice weekly. WARNING! No service oper...

Baixe o seu

Para fazer o download, introduza 2 dígitos :