Log:
Downloads : 6   Arquivo Tamanho: 207 kb   Fabricante : Makita  
Categoria : Máquinas e acabar
@name

Mount the wheel guard with the protrusion on the wheel guard band aligned with the groove on the bearing box. Be sure to tighten both screws securely. To remove wheel guard, follow the installation procedure in reverse. 001078 Installing or removing depressed center grinding wheel/Multi-disc (optional accessory) WARNING: • Always use optional guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. Mount

Downloads : 0   Arquivo Tamanho: 110 kb   Fabricante : Makita  
Categoria : Máquinas e acabar
@name

Electrical shock can cause serious or fatal injury. Follow the National Electrical Code (NEC) and local codes for the safe installation of this equipment. 1. All grounded, cord–connected grinders: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This grinder is equipped with an electric cord having an equipment–grounding conductor and a grounding plug. The plug must be plugged into a matching outl

Downloads : 5   Arquivo Tamanho: 468 kb   Fabricante : Makita  
Categoria : Máquinas e acabar
@name@name@name

The correct power tool will do the job better and safer at the rate for which it was designed. 17. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and 2 must be repaired. must be repaired. 18. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of co

Downloads : 20   Arquivo Tamanho: 468 kb   Fabricante : Makita  
Categoria : Máquinas e acabar
@name@name@name

accessory. Accessory may kickback over your 9. Keep bystanders a safe distance away from hand. work area. Anyone entering the work area c) Do not position your body in the area where must wear personal protective equipment. power tool will move if kickback occurs. Fragments of workpiece or of a broken accessory Kickback will propel the tool in direction opposite to may fly away and cause injury beyond immediate the wheel’s movement at the point of snagging. area of operation. d) Use special care

Downloads : 0   Arquivo Tamanho: 1 mb   Fabricante : Makita  
Categoria : Máquinas e acabar

Downloads : 0   Arquivo Tamanho: 1 mb   Fabricante : Makita  
Categoria : Máquinas e acabar

Downloads : 9   Arquivo Tamanho: 123 kb   Fabricante : Makita  
Categoria : Máquinas e acabar
@name

Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1. 003291 Refer to the figure for the relationship between the number 003291 Refer to the figure for the relationship between the number C range: For regular sanding 12000 NOTE: • The figure shows standard applications. They may differ C 4000 B under certain conditions. A CAUTION: 45 • If the tool is operated continuously at low speeds for a long tim

Downloads : 0   Arquivo Tamanho: 282 kb   Fabricante : Makita  
Categoria : Máquinas e acabar

Downloads : 2   Arquivo Tamanho: 137 kb   Fabricante : Makita  
Categoria : Máquinas e acabar
@name

Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1. Refer to the figure below for the relationship between the number setting on the adjusting dial and the kind of work. 002530 12000 4000 Orbits per minute A B C 1 2 345 Dial setting A range: For polishing B range: For finish sanding C range: For regular sanding NOTE: • The above figure shows standard applications. They may differ under certain cond

Downloads : 4   Arquivo Tamanho: 75 kb   Fabricante : Makita  
Categoria : Máquinas e acabar
@name

Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 2. Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses. 3. Hold the tool firmly. 4. Do not leave the tool running. Operate the tool only when hand-held. 5. This tool has not been waterproofed, so do not use water on the workpiece surface. 6. Ventilate your work area adequately when you perform sanding operations. 7. Use of this tool to sand some products, paint





categorias